ste — Sundance Technologies ST201 Fast Ethernet device driver

       The ste driver was written by Bill Paul <wpaul@ee.columbia.edu>.

Debian                                          December 24, 2009                                         STE(4)

       The  ste driver provides support for PCI Ethernet adapters and embedded controllers based on the Sundance
       Technologies ST201 PCI Fast Ethernet controller chip.

       The Sundance ST201 uses bus master DMA and is designed to be a 3Com Etherlink XL workalike.  It uses  the
       same DMA descriptor structure and is very similar in operation, however its register layout is different.
       The  ST201  has a 64-bit multicast hash filter and a single perfect filter entry for the station address.
       It supports both 10 and 100Mbps speeds in either full or half duplex using an MII transceiver.

       The ste driver supports the following media types:

       autoselect            Enable autoselection of the media type and options.  The user can manually override
                             the autoselected mode by adding media options to the /etc/rc.conf file.

       10baseT/UTP           Set 10Mbps operation.  The mediaopt option  can  also  be  used  to  select  either
                             full-duplex or half-duplex modes.

       100baseTX             Set  100Mbps  (Fast  Ethernet)  operation.  The mediaopt option can also be used to
                             select either full-duplex or half-duplex modes.

       The ste driver supports the following media options:

       full-duplex           Force full duplex operation.

       half-duplex           Force half duplex operation.

       For more information on configuring this device, see ifconfig(8).

ste%d:couldn'tmapports/memory  A fatal initialization error has occurred.

       ste%d:couldn'tmapinterrupt  A fatal initialization error has occurred.

       ste%d:watchdogtimeout  The device has stopped responding to the network, or there is a problem with the
       network connection (cable).

       ste%d:nomemoryforrxlist  The driver failed to allocate an mbuf for the receiver ring.

       ste%d:nomemoryfortxlist    The  driver failed to allocate an mbuf for the transmitter ring when
       allocating a pad buffer or collapsing an mbuf chain into a cluster.

       ste%d:chipisinD3powerstate--settingtoD0  This message applies only to  adapters  which  support
       power  management.  Some operating systems place the controller in low power mode when shutting down, and
       some PCI BIOSes fail to bring the chip out of this state before configuring it.  The controller loses all
       of its PCI configuration in the D3 state, so if the BIOS does not set it back to full power mode in time,
       it will not be able to configure it correctly.  The driver tries to detect this condition and  bring  the
       adapter  back  to  the  D0 (full power) state, but this may not be enough to return the driver to a fully
       operational condition.  If you see this message at boot time and the driver fails to attach the device as
       a network interface, you will have to perform a second warm boot to have the device properly configured.

       Note that this condition only occurs when warm booting from another operating system.  If you power  down
       your system prior to booting FreeBSD, the card should be configured correctly.

       The ste driver supports Sundance Technologies ST201 based Fast Ethernet adapters and embedded controllers
       including:

       •   D-Link DFE-530TXS
       •   D-Link DFE-550TX
       •   D-Link DFE-580TX

       The ste device driver first appeared in FreeBSD 3.0.

       ste — Sundance Technologies ST201 Fast Ethernet device driver

altq(4), arp(4), miibus(4), netintro(4), ng_ether(4), polling(4), vlan(4), ifconfig(8)

       SundanceST201datasheet, http://www.sundanceti.com.

       To compile this driver into the kernel, place the following lines in your kernel configuration file:

             devicemiibusdeviceste

       Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

             if_ste_load="YES"

       The following variables are available as both sysctl(8) variables and loader(8) tunables:

       dev.ste.%d.int_rx_mod
               Maximum number of time to delay RX interrupts.  The valid range is 0 to 209712 in units  of  1us,
               the  default  is 150 (150us).  The value 0 effectively disables the RX interrupt moderation.  The
               resolution of timer is about 3.2us so  finer  tuning  than  3.2us  wouldn't  be  available.   The
               interface does not need to be brought down and up again before a change takes effect.