This manual page is part of the POSIX Programmer's Manual. The Linux implementation of this interface

       None.

       Portions of this text are reprinted and reproduced in electronic form from IEEE Std 1003.1-2017, Standard
       for  Information  Technology  --  Portable  Operating  System  Interface  (POSIX),  The  Open  Group Base
       Specifications Issue 7, 2018 Edition, Copyright (C) 2018 by the Institute of Electrical  and  Electronics
       Engineers, Inc and The Open Group.  In the event of any discrepancy between this version and the original
       IEEE  and The Open Group Standard, the original IEEE and The Open Group Standard is the referee document.
       The original Standard can be obtained online at http://www.opengroup.org/unix/online.html .

       Any typographical or formatting errors that appear in this page are most likely to have  been  introduced
       during   the   conversion  of  the  source  files  to  man  page  format.  To  report  such  errors,  see
       https://www.kernel.org/doc/man-pages/reporting_bugs.html .

IEEE/The Open Group                                   2017                                   SIGEMPTYSET(3POSIX)

       The sigemptyset() function initializes the signal set pointed to by set, such that all signals defined in
       POSIX.1‐2008 are excluded.

       No errors are defined.

       Thefollowingsectionsareinformative.

       None.

       None.

       sigemptyset — initialize and empty a signal set

       This  manual  page  is part of the POSIX Programmer's Manual.  The Linux implementation of this interface
       may differ (consult the corresponding Linux manual page for details of Linux behavior), or the  interface
       may not be implemented on Linux.

       The implementation of the sigemptyset() (or sigfillset()) function could quite trivially clear  (or  set)
       all  the  bits  in  the  signal  set.  Alternatively,  it  would  be reasonable to initialize part of the
       structure, such as a version field, to permit binary-compatibility between releases where the size of the
       set varies. For such reasons, either sigemptyset() or sigfillset() must be called prior to any other  use
       of  the  signal  set,  even if such use is read-only (for example, as an argument to sigpending()).  This
       function is not intended for dynamic allocation.

       The sigfillset() and sigemptyset() functions require that the resulting signal set include  (or  exclude)
       all  the  signals defined in this volume of POSIX.1‐2017. Although it is outside the scope of this volume
       of POSIX.1‐2017 to place  this  requirement  on  signals  that  are  implemented  as  extensions,  it  is
       recommended  that  implementation-defined signals also be affected by these functions. However, there may
       be a good reason for a particular signal not to  be  affected.  For  example,  blocking  or  ignoring  an
       implementation-defined  signal  may  have  undesirable  side-effects, whereas the default action for that
       signal is harmless. In such a case, it would be preferable for such a signal  to  be  excluded  from  the
       signal set returned by sigfillset().

       In  early  proposals  there  was  no  distinction  between  invalid and unsupported signals (the names of
       optional signals that were not supported by an implementation were not defined by  that  implementation).
       The  [EINVAL] error was thus specified as a required error for invalid signals. With that distinction, it
       is not necessary to require implementations of these functions to determine whether an optional signal is
       actually supported, as that could have a significant performance impact for little value. The error could
       have  been  required  for  invalid  signals  and  optional  for  unsupported  signals,  but  this  seemed
       unnecessarily complex. Thus, the error is optional in both cases.

       Upon  successful completion, sigemptyset() shall return 0; otherwise, it shall return -1 and set errno to
       indicate the error.

Section2.4, SignalConcepts, pthread_sigmask(), sigaction(), sigaddset(), sigdelset(), sigfillset(),
       sigismember(), sigpending(), sigsuspend()

       The Base Definitions volume of POSIX.1‐2017, <signal.h>

       #include <signal.h>

       int sigemptyset(sigset_t *set);