ipmiutil_fru - show Field Replaceable Unit configuration data

       Andy Cress <arcress at users.sourceforge.net>

                                            Version 1.4: 09 Sep 2010                                     IFRU(8)

       Copyright (C) 2009  Kontron America, Inc.

       See the file COPYING in the distribution for more details regarding redistribution.

       This utility is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY.

ipmiutilfru is a program that uses IPMI commands to show FRU configuration data and optionally write an
       asset tag string into the FRU data.  Setting the asset tag is a function that can  be  used  to  uniquely
       identify  the  unit, even if the storage devices are removed or changed.  This utility can use either the
       /dev/ipmi0 driver from OpenIPMI, the /dev/imb driver from Intel, the /dev/ipmikcs  driver  from  valinux,
       direct user-space IOs, or the IPMI LAN interface if -N.

       ipmiutil_fru - show Field Replaceable Unit configuration data

       Command line options are described below.

       -a asset_string
              This  option  specifies  an asset tag string to be written to the baseboard FRU Product area.  The
              asset tag length is limited by the existing FRU Product data, but is  usually  allowed  up  to  16
              characters.  The default is to not modify this FRU field.

       -b     Only  show  the  Baseboard FRU data.  The default behavior is to also scan for any SDR FRU data or
              DIMM SPD data referenced by the SDRs.

       -c     Show FRU output in a canonical format, with a default delimiter of '|'.

       -d file
              Dump binary FRU data to the specified file.

       -e     Show Every FRU output in a bladed chassis, including those under child MCs.   The  default  is  to
              show FRUs referred to by just the target MC.

       -i 00  This option specifies a specific FRU ID to show.  The input value should be in hex (0b, 1a, etc.),
              as  shown  from  the  sensor  SDR  output.   By default, all FRU IDs that are specified in the FRU
              locator SDRs are shown.

       -k <setsn | setmfgdate | nextboot>
              These Kontron OEM functions set FRU data based on  existing  data  stored  elsewhere.   The  setsn
              option  sets the FRU Board and Product serial number, and the setmfgdate option sets the FRU Board
              Mfg DateTime.  The nextboot option specifies the boot device for the next boot:  BIOS,  FDD,  HDD,
              CDROM,  or  network.   These  options  are  only  supported on Kontron ATCA boards which have this
              functionality.

       -m 002000
              Show FRU for a specific MC (e.g. bus 00, sa 20, lun 00).  This could be used  for  PICMG  or  ATCA
              blade  systems.   The  trailing  character,  if  present, indicates SMI addressing if 's', or IPMB
              addressing if 'i' or not present.

       -s serial_num
              This option specifies a serial number string to be written to the baseboard FRU Product area.  The
              serial number can be any string up to 16 characters.  The default is to not modify this FRU field.

       -v prod_ver
              This option specifies a product version number string to be written to the baseboard  FRU  Product
              area.   The  version  number  can be any string up to 16 characters.  The default is to not modify
              this FRU field.

       -x     Causes eXtra debug messages to be displayed.

       -N nodename
              Nodename or IP address of the remote  target  system.   If  a  nodename  is  specified,  IPMI  LAN
              interface is used.  Otherwise the local system management interface is used.

       -U rmt_user
              Remote username for the nodename given.  The default is a null username.

       -P/-R rmt_pswd
              Remote password for the nodename given.  The default is a null password.

       -E     Use the remote password from Environment variable IPMI_PASSWORD.

       -F drv_t
              Force  the driver type to one of the followng: imb, va, open, gnu, landesk, lan, lan2, lan2i, kcs,
              smb.  Note that lan2i means lan2 with intelplus.  The default is to detect  any  available  driver
              type and use it.

       -J     Use   the  specified  LanPlus  cipher  suite  (0  thru  17):  0=none/none/none,  1=sha1/none/none,
              2=sha1/sha1/none, 3=sha1/sha1/cbc128, 4=sha1/sha1/xrc4_128, 5=sha1/sha1/xrc4_40,  6=md5/none/none,
              ... 14=md5/md5/xrc4_40.  Default is 3.

       -T     Use a specified IPMI LAN Authentication Type: 0=None, 1=MD2, 2=MD5, 4=Straight Password, 5=OEM.

       -V     Use  a  specified  IPMI  LAN  privilege  level.  1=Callback level, 2=User level, 3=Operator level,
              4=Administrator level (default), 5=OEM level.

       -Y     Yes, do prompt the user for the IPMI LAN remote password.  Alternatives for the password are -E or
              -P.

       -Z     Set the slave address for a local MC

ipmiutil(8)  ialarms(8)  iconfig(8)  icmd(8)  idiscover(8)  ievents(8)  igetevent(8)  ihealth(8)  ilan(8)
       ireset(8) isel(8) isensor(8) iserial(8) isol(8) iwdt(8)

ipmiutilfru[-abcdeikmsvx-Nnode-Uuser-P/-Rpswd-EFJTVYZ]

       See http://ipmiutil.sourceforge.net/ for the latest version of ipmiutil and any bug fix list.