sg_rep_density - send SCSI REPORT DENSITY SUPPORT command

       Written by Douglas Gilbert.

       Copyright © 2022-2023 Douglas Gilbert
       This  software  is  distributed  under  a  BSD-2-Clause  license.  There  is  NO  warranty;  not even for
       MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.

       Sends a SCSI REPORT DENSITY command to DEVICE and outputs the data returned. This command is  tape  drive
       specific.  This  command is found in the SSC-5 draft standard, revision 6 (ssc5r06.pdf). This command was
       present in the SSC-2 standard (ANSI INCITS 380-2003).

       By default this utility requests the density code descriptors supported by the DEVICE (e.g. a tape drive)
       and decodes the response. If the --typem option is given it fetches the medium type descriptors supported
       by the DEVICE and decodes the response. When the --media option is given the density code or medium  type
       descriptors supported by the media inside the DEVICE (e.g. a tape cartridge) are fetched.

       The exit status of sg_rep_density is 0 when it is successful. Otherwise see the sg3_utils(8) man page.

       sg_rep_density - send SCSI REPORT DENSITY SUPPORT command

       Arguments to long options are mandatory for short options as well.

       -h, --help
              output the usage message then exit.

       -H, --hex
              output the response in hexadecimal to stdout. When used once the whole response is output in ASCII
              hexadecimal,  prefixed  by  an  address  (starting  at  0) on each line. When used twice the whole
              response is output in hexadecimal with no leading address (on each line).
              Using this option three times will produce output that can be redirected to a file and later given
              to another invocation using the --inhex=FN option.

       -i, --inhex=FN
              where FN is a file name whose contents are assumed to be ASCII  hexadecimal.  If  DEVICE  is  also
              given  then  DEVICE  is  ignored, a warning is issued and the utility continues, decoding the file
              named FN. See the "HEX, BINARY AND JSON  FORMATS"  section  in  the  sg3_utils  manpage  for  more
              information. If the --raw option is also given then the contents of FN are treated as binary.

       -m, --maxlen=LEN
              where LEN is the (maximum) response length in bytes. It is placed in the cdb's "allocation length"
              field. If not given (or LEN is zero) then 8192 is used. The maximum allowed value of LEN is 65535.

       -M, --media
              sets  the  MEDIA  bit in the cdb which causes the density codes (or medium types) supported by the
              tape cartridge in the drive to be placed in the response. The default is to  request  the  density
              codes (or medium types) supported by the tape drive itself.
              If there is no "medium" (e.g. tape cartridge) present in the drive the SCSI command will fail with
              a "not ready" sense key.

       -r, --raw
              output  the  SCSI  response (i.e. the data-out buffer) in binary (to stdout) unless the --inhex=FN
              option is given.
              When used together with the --inhex=FN option then the  contents  of  FN  are  treated  as  binary
              (rather than hexadecimal).

       -R, --readonly
              open  the  DEVICE  read-only  (e.g.  in  Unix  with the O_RDONLY flag).  The default is to open it
              read-write.

       -t, --typem
              sets the MEDIUM TYPE bit in the cdb which causes the medium types supported by the tape drive  (or
              tape cartridge) to be placed in the response. The default is to request the density codes.

       -v, --verbose
              increase the level of verbosity, (i.e. debug output).

       -V, --version
              print the version string and then exit.

       Report bugs to <dgilbert at interlog dot com>.

sg3_utils(sg3_utils)

sg3_utils-1.48                                      June 2023                                  SG_REP_DENSITY(8)

sg_rep_density  [--help]  [--hex]  [--inhex=FN]  [--maxlen=LEN]  [--media] [--raw] [--readonly] [--typem]
       [--verbose] [--version] DEVICE