opaextractlids

       -h 0

                 First active port in system (Default).

       -h 0 -p 0

                 First active port in system.

       -h x

                 First active port on HFI x.

       -h x -p 0

                 First active port on HFI x.

       -h 0 -p y

                 Port y within system (no matter which ports are active).

       -h x -p y

                 HFI x, port y.

       # List all the lids in the fabric:

       opaextractlids

       # List all the lids of end-nodes:

       opaextractlids -F "nodetype:FI"

       # List all the lids on the 2nd HFI's fabric of a multi-plane fabric:

       opaextractlids -h 2

Copyright(C) 2015-2019                          Intel Corporation                              opaextractlids(8)

       opaextractlids

       Produces  a  CSV file listing all or some of the LIDs in the fabric. opaextractlids is a front end to the
       opareport tool. The output from this tool can be imported into a spreadsheet or parsed by other scripts.

       --help

                 Produces full help text.

       opareport options

                 The following options are passed to opareport. This subset is considered typical and useful for
                 this command. By design, the tool ignores -o/--output report option.

                 -h/--hfi hfi
                           Specifies the HFI, numbered 1..n. Using 0 specifies  that  the  -p  port  port  is  a
                           system-wide port number. Default is 0.

                 -p/--port port
                           Specifies  the  port, numbered 1..n. Using 0 specifies the first active port. Default
                           is 0.

                 -X/--infile snapshot_input
                           Generates a report using the data in the  snapshot_input  file.  snapshot_input  must
                           have been generated during a previous -o snapshot run. When used, the -s, -i, -C, and
                           -a options are ignored. '-' may be used as the snapshot_input to specify stdin.

                 -F/--focus point
                           Specifies the focus area for report. Used for all reports except route to limit scope
                           of report. Refer to PointSyntax for details.

       gid:valuevalue is numeric port GID of form: subnet:guid.

       lid:valuevalue is numeric LID.

       lid:value:node

                 value is numeric LID, selects entire node with given LID.

       lid:value:port:value2value is numeric LID of node, value2 is port number.

       portguid:valuevalue is numeric port GUID.

       nodeguid:valuevalue is numeric node GUID.

       nodeguid:value1:port:value2value1 is numeric node GUID, value2 is port number.

       iocguid:valuevalue is numeric IOC GUID.

       iocguid:value1:port:value2value1 is numeric IOC GUID, value2 is port number.

       systemguid:valuevalue is numeric system image GUID.

       systemguid:value1:port:value2value1 is the numeric system image GUID, value2 is port number.

       ioc:valuevalue is IOC Profile ID String (IOC Name).

       ioc:value1:port:value2value1 is IOC Profile ID String (IOC Name), value2 is port number.

       iocpat:valuevalue is glob pattern for IOC Profile ID String (IOC Name).

       iocpat:value1:port:value2value1 is glob pattern for IOC Profile ID String (IOC Name), value2 is port number.

       ioctype:valuevalue is IOC type (SRP or OTHER).

       ioctype:value1:port:value2value1 is IOC type (SRP or OTHER); value2 is port number.

       node:valuevalue is node description (node name).

       node:value1:port:value2value1 is node description (node name), value2 is port number.

       nodepat:valuevalue is glob pattern for node description (node name).

       nodepat:value1:port:value2value1 is the glob pattern for the node description (node name), value2 is port number.

       nodedetpat:valuevalue is glob pattern for node details.

       nodedetpat:value1:port:value2value1 is the glob pattern for the node details, value2 is port number.

       nodetype:valuevalue is node type (SW or FI).

       nodetype:value1:port:value2value1 is node type (SW or FI), value2 is port number.

       rate:valuevalue is string for rate (25g, 50g, 75g, 100g), omits switch mgmt port 0.

       portstate:valuevalue is a string for state (down, init, armed, active, notactive, initarmed).

       portphysstate:valuevalue is a string for PHYs state (polling, disabled, training, linkup, recovery, offline, test)

       mtucap:valuevalue is MTU size (2048, 4096, 8192, 10240), omits switch mgmt port 0.

       labelpat:valuevalue is glob pattern for cable label.

       lengthpat:valuevalue is glob pattern for cable length.

       cabledetpat:valuevalue is glob pattern for cable details.

       cabinflenpat:valuevalue is glob pattern for cable info length.

       cabinfvendnamepat:valuevalue is glob pattern for cable info vendor name.

       cabinfvendpnpat:valuevalue is glob pattern for cable info vendor part number.

       cabinfvendrevpat:valuevalue is glob pattern for cable info vendor revision.

       cabinfvendsnpat:valuevalue is glob pattern for cable info vendor serial number.

       cabinftype:valuevalue is either optical, passive_copper, active_copper, or unknown.

       linkdetpat:valuevalue is glob pattern for link details.

       portdetpat:valuevalue is glob pattern for port details.

       sm

                 Specifies the master subnet manager (SM).

       smdetpat:valuevalue is glob pattern for SM details.

       route:point1:point2

                 Specifies all ports along the routes between the two given points.

       led:valuevalue is either on or off for LED port beacon.

       linkqual:value

                 Specifies the ports with a link quality equal to value.

       linkqualLE:value

                 Specifies the ports with a link quality less than or equal to value.

       linkqualGE:value

                 Specifies the ports with a link quality greater than or equal to value.

       nodepatfile:FILENAME

                 Specifies the name of file with the list of nodepats or node descriptions.

       nodepairpatfile:FILENAME

                 Specifies the name of file with the list of node pairs, separated by a colon.

       ldr

                 Specifies the ports with a non-zero link down reason or neighbor link down reason.

       ldr:value

                 Specifies the ports with a link down reason or neighbor link down reason equal to value.

       opaextractlids [opareport  options]