ProgrammingMethods:-dprog=<method>
avr910 Standard Atmel Serial Programmer/Atmel Low Cost Programmer
pavr http://www.avr1.org/pavr/pavr.html
stk500 Atmel STK500
dapa Direct AVR Parallel Access
stk200 Parallel Starter Kit STK200, STK300
abb Altera ByteBlasterMV Parallel Port Download Cable
atdh Atmel-ISP Download Cable (P/N ATDH1150VPC)
avrisp Atmel AVR ISP (?)
bsd http://www.bsdhome.com/avrdude/ (parallel)
fbprg http://ln.com.ua/~real/avreal/adapters.html (parallel)
dt006 http://www.dontronics.com/dt006.html (parallel)
maxi Investment Technologies Maxi (parallel)
dm04 Datamekatronik 2004 (parallel)
dasa serial (RESET=RTS SCK=DTR MOSI=TXD MISO=CTS)
dasa2 serial (RESET=!TXD SCK=RTS MOSI=DTR MISO=CTS)
dasa3 serial (RESET=!DTR SCK=RTS MOSI=TXD MISO=CTS)
TargetDeviceSelection:-dpart=part
Set target abbreviated name or number. For some programmers, if -dpart is not given programmer's
supported devices are listed. Set -dpart=auto for auto-select. Auto-select does not work with all
programmers, so it is recommended to always specify a target device explicitly.
ParallelDeviceSettings:-dlpt=address|device name
specify device name (Linux ppdev, FreeBSD ppi, serial) or direct I/O parallel port address (0x378,
0x278, 0x3BC)
-dno-poll
Program without data polling (a little slower)
-dno-retry
Disable retries of program enable command
-dvoltage=value
Set timing specs according to the power supply voltage in [V] (default 3.0)
-dt_sck=time
Set minimum SCK high/low time in micro-seconds (default 5)
-dt_wd_flash=time
Set FLASH maximum write delay time in micro-seconds
-dt_wd_eeprom=time
Set EEPROM maximum write delay time in micro-seconds
-dt_reset=time
Set reset inactive (high) time in micro-seconds
-dinvert=[sck[,mosi[,miso[,reset]]]]]
Invert specified lines Use -v=3 option to see current settings.
-d89 Allow parallel programming of AT89S51 and AT89S52 devices.
AtmelLowCostProgrammerSerialDeviceSettings:-dserial=device name
Set serial interface as /dev/ttyS* (default /dev/avr)
-dspeed=1200|2400|4800|9600|19200|38400|57600|115200
Set speed of the serial interface (default 19200)
Stk500specificoptions:-dhiv Use Hi-V programming instead of SPI (default is SPI).
--rd_aref
Read the ARef Voltage. Note that due to a bug in the stk500 firmware, the read value is sometimes
off by 0.1 from the actual value measured with a volt meter.
--wr_aref=value
Set the ARef Voltage. Valid values are 0.0 to 6.0 volts in 0.1 volt increments. Value can not be
larger than the VTarget value.
--rd_vtg
Read the Vtarget Voltage. Note that due to a bug in the stk500 firmware, the read value is
sometimes off by 0.1 from the actual value measured with a volt meter.
--wr_vtg=value
Set the VTarget Voltage. Valid values are 0.0 to 6.0 volts in 0.1 volt increments. Value can not
be smaller than the ARef value.
--rd_osc
Read the oscillator frequency in Hertz.
--wr_osc=value
Set the oscillator frequency in Hertz, from 14.06 to 3686400.
Functions:--upload
Upload "input_file" to the AVR memory.
--verify
Verify "input_file" (processed after the --upload opt.)
--download
Download AVR memory to "output_file" or stdout.
--erase
Erase device.
--segment=flash|eeprom|fuse
Set active segment (auto-select for AVA Motorola output)
Fuse/LockBitOperations:--rd_fuses
Read all fuses and print values to stdout
--wr_fuse_l=byte
Write fuse low byte
--wr_fuse_h=byte
Write fuse high byte
--wr_fuse_e=byte
Write fuse extended byte
--wr_lock=byte
Write lock bits. Argument is a byte where each bit is:
Bit5 -> blb12
Bit4 -> blb11
Bit3 -> blb02
Bit2 -> blb01
Bit1 -> lb2
Bit0 -> lb1
--lock Write lock bits [old method; deprecated].
Files:if=filename
Input file for the --upload and --verify functions in Motorola S-records (S1 or S2) or 16 bit
Intel format
of=filename
Output file for the --download function in Motorola S-records format, default is standard output
OtherOptions:-v=level
Set verbose level (-v equals -v=2, min/max: 0/4, default 1)
--hash=perbytes
Print hash (default is 32 bytes)
--help-h
Help
--version
Print version information
--terminal
Invoke shell-like terminal
Install Now
