-h, --help
Displays this help.
-v, --version
Displays version information.
-b, --basename <The base filename of layout files>
The base filename of exported layout files. Use it to enable console exportmode.
-d, --destination <The destination folder>
The path to output destination folder. By default the directory at which the application was
started. The path must exists and be reachable for the program.
-m, --mfile <The measure file>
Path to custom measure file (exportmode).
-n, --time <Time>
<Time> in minutes given for the algorithm to find best layout (exportmode). Time must be in range
from 1 minute to 60 minutes. Default value 1 minute.
--coefficient <Coefficient>
Set layout efficiency coefficient (exportmode). Layout efficiency coefficient is the ratio of the
area occupied by the pieces to the bounding rect of all pieces. If nesting reaches required level
the process stops. If value is 0 no check will be made. Coefficient must be in range from 0 to
100. Default value 0.
-f, --format <Format number>
Number corresponding to output format (default = 0, exportmode):
* Svg files (*.svg) = 0,
* PDF files (*.pdf) = 1,
* Image files (*.png) = 2,
* Wavefront OBJ (*.obj) = 3,
* PS files (*.ps) = 4,
* EPS files (*.eps) = 5,
* AutoCAD DXF R10 (flat) files (*.dxf) = 6,
* AutoCAD DXF R11/12 (flat) files (*.dxf) = 7,
* AutoCAD DXF R13 (flat) files (*.dxf) = 8,
* AutoCAD DXF R14 (flat) files (*.dxf) = 9,
* AutoCAD DXF 2000 (flat) files (*.dxf) = 10,
* AutoCAD DXF 2004 (flat) files (*.dxf) = 11,
* AutoCAD DXF 2007 (flat) files (*.dxf) = 12,
* AutoCAD DXF 2010 (flat) files (*.dxf) = 13,
* AutoCAD DXF 2013 (flat) files (*.dxf) = 14,
* AutoCAD DXF R10 AAMA files (*.dxf) = 15,
* AutoCAD DXF R11/12 AAMA files (*.dxf) = 16,
* AutoCAD DXF R13 AAMA files (*.dxf) = 17,
* AutoCAD DXF R14 AAMA files (*.dxf) = 18,
* AutoCAD DXF 2000 AAMA files (*.dxf) = 19,
* AutoCAD DXF 2004 AAMA files (*.dxf) = 20,
* AutoCAD DXF 2007 AAMA files (*.dxf) = 21,
* AutoCAD DXF 2010 AAMA files (*.dxf) = 22,
* AutoCAD DXF 2013 AAMA files (*.dxf) = 23,
* AutoCAD DXF R10 ASTM файли (*.dxf) = 24,
* AutoCAD DXF R11/12 ASTM файли (*.dxf) = 25,
* AutoCAD DXF R13 ASTM файли (*.dxf) = 26,
* AutoCAD DXF R14 ASTM файли (*.dxf) = 27,
* AutoCAD DXF 2000 ASTM файли (*.dxf) = 28,
* AutoCAD DXF 2004 ASTM файли (*.dxf) = 29,
* AutoCAD DXF 2007 ASTM файли (*.dxf) = 30,
* AutoCAD DXF 2010 ASTM файли (*.dxf) = 31,
* AutoCAD DXF 2013 ASTM файли (*.dxf) = 32,
* PDF tiled files (*.pdf) = 33,
* TIFF файли (*.tif) = 35.
--bdxf Export dxf in binary form.
--text2paths
Export text as paths.
--exportOnlyDetails
Export only details. Export details as they positioned in the details mode. Any layout related
options will be ignored.
--exportSuchDetails <The name regex>
Export only details that match a piece name regex.
--dimensionA <The dimension A base>
Set base for dimension A in the multisize measurements units (exportmode).
--dimensionB <The dimension B base>
Set base for dimension B in the multisize measurements units (exportmode).
--dimensionC <The dimension C base>
Set base for dimension C in the multisize measurements units (exportmode).
--userMaterial <User material>
Use this option to override user material defined in pattern. The value must be in form
<number>@<user matrial name>. The number should be in range from 1 to 20. For example, 1@Fabric2.
The key can be used multiple times. Has no effect in GUI mode.
-p, --pageformat <Template number>
Number corresponding to layout page template (default = 0, exportmode):
* A0 = 0,
* A1 = 1,
* A2 = 2,
* A3 = 3,
* A4 = 4,
* Letter = 5,
* Legal = 6,
* Tabloid = 7,
* Roll 24in = 8,
* Roll 30in = 9,
* Roll 36in = 10,
* Roll 42in = 11,
* Roll 44in = 12,
* Roll 48in = 13,
* Roll 62in = 14,
* Roll 72in = 15.
--landscapeOrientation
Switch page template orientation to landscape (exportmode). This option has effect only for one
of predefined page templates.
-W, --pagew <The page width>
Page width in current units like 12.0 (cannot be used with “pageformat”, exportmode).
-H, --pageh <The page height>
Page height in current units like 12.0 (cannot be used with “pageformat”, exportmode).
-U, --pageunits <The measure unit>
Page measure units (exportmode). Valid values: mm, cm, inch, px.
-i, --ignoremargins
Ignore margins printing (exportmode). Use if need full paper space. In case of later printing you
must account for the margins himself.
-L, --lmargin <The left margin>
Page left margin in current units like 3.0 (exportmode). If not set will be used value from
default printer. Or 0 if none printers was found.
-R, --rmargin <The right margin>
Page right margin in current units like 3.0 (exportmode). If not set will be used value from
default printer. Or 0 if none printers was found.
-T, --tmargin <The top margin>
Page top margin in current units like 3.0 (exportmode). If not set will be used value from
default printer. Or 0 if none printers was found.
-B, --bmargin <The bottom margin>
Page bottom margin in current units like 3.0 (exportmode). If not set will be used value from
default printer. Or 0 if none printers was found.
--xscale <Horizontal scale>
Set horizontal scale factor from 0.01 to 3.0 (default = 1.0, exportmode).
--yscale <Vertical scale>
Set vertical scale factor from 0.01 to 3.0 (default = 1.0, exportmode).
--followGrainline
Order detail to follow grainline direction (exportmode).
--manualPriority
Follow manual priority over priority by square (exportmode).
--nestQuantity
Nest quantity copies of each piece (exportmode).
-c, --crop
Auto crop unused length (exportmode).
--cropWidth
Auto crop unused width (exportmode).
-u, --unite
Unite pages if possible (exportmode). Maximum value limited by QImage that supports only a
maximum of 32768x32768px images.
--preferOneSheetSolution
Prefer one sheet layout solution (exportmode).
-S, --savelen
Save length of the sheet if set (exportmode). The option tells the program to use as much as
possible width of sheet. Quality of a layout can be worse when this option was used.
-l, --layounits <The unit>
Layout units (as paper's one except px, exportmode).
-G, --gapwidth <The gap width>
The layout gap width x2, measured in layout units (exportmode). Set distance between details and
a detail and a sheet.
-g, --groups <Grouping type>
Sets layout groupping cases (exportmode):
* Three groups: big, middle, small = 0,
* Two groups: big, small = 1,
* Descending area = 2.
-t, --test
Run the program in a test mode. The program in this mode loads a single pattern file and silently
quit without showing the main window. The key have priority before key “basename”.
--pedantic
Make all parsing warnings into errors. Have effect only in console mode. Use to force Valentina to
immediately terminate if a pattern contains a parsing warning.
--no-scaling
Disable high dpi scaling. Call this option if has problem with scaling (by default scaling
enabled). Alternatively you can use the QT_AUTO_SCREEN_SCALE_FACTOR=0 environment variable.
--csvWithHeader
Export to csv with header. By default disabled.
--csvCodec <Codec name>
Specify codec that will be used to save data. List of supported codecs provided by Qt. Default
value depend from system. On Windows, the codec will be based on a system locale. On Unix systems,
the codec will might fall back to using the iconv library if no builtin codec for the locale can
be found. Valid values usually these:
* US-ASCII,
* US-ASCII,
* ISO-8859-1,
* ISO-8859-2,
* ISO-8859-3,
* ISO-8859-4,
* ISO-8859-5,
* ISO-8859-6,
* ISO-8859-7,
* ISO-8859-8,
* ISO-8859-9,
* ISO-8859-10,
* ISO-2022-JP-1,
* Shift_JIS,
* EUC-JP,
* US-ASCII,
* windows-949,
* ISO-2022-KR,
* windows-949,
* ISO-2022-JP,
* ISO-2022-JP-2,
* GBK,
* ISO-8859-6,
* ISO-8859-6,
* ISO-8859-8,
* ISO-8859-8,
* ISO-2022-CN,
* ISO-2022-CN-EXT,
* UTF-8,
* ISO-8859-13,
* ISO-8859-14,
* ISO-8859-15,
* GBK,
* GB18030,
* UTF-16,
* UTF-32,
* SCSU,
* UTF-7,
* UTF-16BE,
* UTF-16LE,
* UTF-16,
* CESU-8,
* UTF-32,
* UTF-32BE,
* UTF-32LE,
* BOCU-1,
* hp-roman8,
* Adobe-Standard-Encoding,
* IBM850,
* IBM862,
* IBM-Thai,
* Shift_JIS,
* GBK,
* Big5,
* macintosh,
* IBM037,
* IBM273,
* IBM277,
* IBM278,
* IBM280,
* IBM284,
* IBM285,
* IBM290,
* IBM297,
* IBM420,
* IBM424,
* IBM437,
* IBM500,
* cp851,
* IBM852,
* IBM855,
* IBM857,
* IBM860,
* IBM861,
* IBM863,
* IBM864,
* IBM865,
* IBM868,
* IBM869,
* IBM870,
* IBM871,
* IBM918,
* IBM1026,
* KOI8-R,
* HZ-GB-2312,
* IBM866,
* IBM775,
* KOI8-U,
* IBM00858,
* IBM01140,
* IBM01141,
* IBM01142,
* IBM01143,
* IBM01144,
* IBM01145,
* IBM01146,
* IBM01147,
* IBM01148,
* IBM01149,
* Big5-HKSCS,
* IBM1047,
* windows-1250,
* windows-1251,
* windows-1252,
* windows-1253,
* windows-1254,
* windows-1255,
* windows-1256,
* windows-1257,
* windows-1258,
* TIS-620,
* TSCII.
--csvSeparator <Separator character>
Specify csv separator character. Default value is ','. Valid characters:
* 'Tab',
* ';',
* 'Space',
* ','.
--csvExportFM <Path to csv file>
Calling this command enable exporting final measurements. Specify path to csv file with final
measurements. The path must contain path to directory and name of file. It can be absolute or
relatetive. In case of relative path will be used current working directory to calc a destination
path.
--tiledPageformat <Template number>
Number corresponding to tiled pdf page template (default = 0, exportmodewithtiledpdfformat):
* A0 = 0,
* A1 = 1,
* A2 = 2,
* A3 = 3,
* A4 = 4,
* Letter = 5,
* Legal = 6,
* Tabloid = 7.
--tiledlmargin <The left margin>
Tiled page left margin in current units like 3.0 (exportmode). If not set will be used default
value 1 cm.
--tiledrmargin <The right margin>
Tiled page right margin in current units like 3.0 (exportmode). If not set will be used default
value 1 cm.
--tiledtmargin <The top margin>
Tiled page top margin in current units like 3.0 (exportmode). If not set will be used value
default value 1 cm.
--tiledbmargin <The bottom margin>
Tiled page bottom margin in current units like 3.0 (exportmode). If not set will be used value
default value 1 cm.
--tiledLandscape
Set tiled page orienatation to landscape (exportmode). Default value if not set portrait.
Arguments:
filename - a pattern file.
Install Now
PNG Icons
