amuleweb - aMule web server

       This manpage was written by Vollstrecker <amule@vollstreckernet.de>

aMule webserver v2.3.2                           September 2016                                      AMULEWEB(1)

       aMule and all of its related utilities are distributed under the GNU General Public License.

amuleweb manages your access to amule through a web  browser.   You  can  start  amuleweb  together  with
       amule(1),  or  separately, any time later.  Options can be specified via command-line or via config-file.
       Command-line options take precedence over config-file options.

       [-h<host>, --host=<host>]
              Host where aMule is running (default: localhost).  <host> might be an IP address or a DNS name

       [-p<port>, --port=<port>]
              aMule's port for External Connections, as set in Preferences->Remote Controls (default: 4712)

       [-P<password>, --password=<password>]
              External Connections password.

       [-f<path>, --config-file=<path>]
              Use the given configuration file.  Default configuration file is ~/.aMule/remote.conf[-q, --quiet]
              Do not print any output to stdout.

       [-v, --verbose]
              Be verbose - show also debug messages.

       [-l<lang>, --locale=<lang>]
              Sets program locale (language).   See  the  NOTES  section  for  the  description  of  the  <lang>
              parameter.

       [-w, --write-config]
              Write command line options to config file and exit

       [-t<name>, --template=<name>]
              Loads the template named <name>. See the SKINSUPPORT section for details.

       [-s<port>, --server-port=<port>]
              Webserver's HTTP port. This is the port you must point your browser to (default: 4711).

       [-u]
              Enable UPnP.

       [-U<port>, --upnp-port<port>]
              UPnP port.

       [-z, --enable-gzip]
              Enables using gzip compression in HTTP traffic to save bandwidth.

       [-Z, --disable-gzip]
              Disables using gzip compression (this is the default).

       [-A<passwd>, --admin-pass=<passwd>]
              Full access password for webserver.

       [-G<passwd>, --guest-pass=<passwd>]
              Guest password for webserver.

       [-a, --allow-guest]
              Allows guest access.

       [-d, --deny-guest]
              Denies guest access (default).

       [-L, --load-settings]
              Load/save  webserver  settings  from/to remote aMule.  This causes amuleweb to ignore command-line
              and config-file settings, and load them from aMule.  When saving preferences none will be  written
              to  the config file, but to aMule.  (Of course, this works only for those settings that can be set
              in aMule's Preferences->Remote Controls.)

       [--no-php]
              Disable PHP interpreter (deprecated)

       [-N, --no-script-cache]
              Recompiles PHP pages on each request.

       [--create-config-from=<path>]
              Create config file based upon <path>, which must point to a valid  aMule  config  file,  and  then
              exit.

       [--help]
              Prints a short usage description.

       [--version]
              Displays the current version number.

       [--amule-config-file=<path>]
              aMule  config  file  path.  DONOTUSEDIRECTLY!  aMule uses this option when starting amuleweb at
              aMule startup.  This option causes all other command-line and config-file settings to be  ignored,
              preferences to be read from the given config file, and also implies the -q-L options.

       Typically amuleweb will be first run as:

       amuleweb-hhostname-pECport-PECpassword-sHTTPport-AAdminPassword-w

       or

       amuleweb--create-config-from=/home/username/.aMule/amule.conf

       These will save settings to $HOME/.aMule/remote.conf, and later you only need to type:

       amuleweb

       Of course, you may specify any more or less options on the first example line, and you may  also  totally
       omit it.

~/.aMule/remote.conf~/.aMule/webserver/$(pkgdatadir)/webserver/

       amuleweb - aMule web server

Paths
       For  all  options  which  take  a <path> value, if the path contains no directory part (i.e. just a plain
       filename), then it is considered to be under the aMule configuration directory, ~/.aMule.

   Languages
       The <lang> parameter for the -l option has the following  form:  lang[_LANG][.encoding][@modifier]  where
       lang  is  the primary language, LANG is a sublanguage/territory, encoding is the character set to use and
       modifier allows the user to select a specific instance of localization data within a single category.

       For example, the following strings are valid:
              de
              de_DE
              de_DE.iso88591
              de_DE@euro
              de_DE.iso88591@euro

       Though all the above strings are accepted as valid language definitions, encoding and  modifier  are  yet
       unused.

       In  addition  to  the format above, you can also specify full language names in English - so -lgerman is
       also valid and is equal to -lde_DE.

       When no locale is defined, either on command-line or in config file,  system  default  language  will  be
       used.

       Please   report   bugs   either   on   our   forum   (http://forum.amule.org/),   or  in  our  bugtracker
       (http://bugs.amule.org/).  Please do not report bugs in e-mail, neither to our mailing list nor  directly
       to any team member.

amule(1), amulecmd(1)

amuleweb  is capable of displaying information in different skins.  These skins are called templates, and
       you can make amuleweb load a specific template via the -t command line option.  Templates are searched in
       two places: first in ~/.aMule/webserver/ and then in /usr/share/amule/webserver/ if  you  installed  with
       --prefix=/usr.

       Each  template  must be in a subdirectory of the template name, and this directory must contain all files
       the template needs.

amuleweb  [-h<host>] [-p<port>] [-P<password>] [-f<path>] [-q] [-v] [-l<lang>] [-w] [-t<name>] [-s<port>] [-u] [-U<port>] [-z] [-Z] [-A<password>] [-G<password>] [-a|-d] [-L] [--no-php] [-N]

       amuleweb [--create-config-from=<path>]

       amuleweb [--help]

       amuleweb [--version]

       amuleweb [--amule-config-file=<path>]