uuids
Set/Get advertise uuids.
Usage#uuids[all/uuid1uuid2...]Example#uuids0x1234Example#uuids0x12345678Example#uuids90f95193-35de-4306-a6e9-699328f15059service
Set/Get advertise service data.
Usage#service[uuid][data=xxxx...]manufacturer
Set/Get advertise manufacturer data.
Updating is in real time while advertising. This is currently limited to 25 bytes and will return an
error message of "Too much data" if that maximum has been exceeded. However, this does not check if the
advertising payload length maximum has been exceeded so you may receive an error from bluetoothd that it
"Failed to register advertisement" which means you need to reduce your manufacturer data length.
Usage#manufacturer[id][data=xxxx...]data
Set/Get advertise data.
This allows you to advertise data with a given type. You cannot use a registered data type value {1} with
this command. For LE the advertising shows up in the primary advertisements.
If you set only the type of the data without any data (data 0x0c) this will cause a parse error when
turning advertise on.
You can modify the advertising data while it is advertising.
To get the currently set data use the command data without any arguments.
Usage#data[type][data=xxxx...]Example#data0x0C010x0F13discoverable
Set/Get advertise discoverable.
For LE discoverable on will set the LE General Discoverable Mode flag to true in the primary
advertisement if on.
This feature can be changed during advertising, but will only trigger LE General Discoverable Mode even
if you had previously selected discoverable-timeout this will be ignored.
Entering the command by itself will show the status of the setting
Usage#discoverable[on/off]discoverable-timeout
Set/Get advertise discoverable timeout.
Using this feature in LE will cause the LE Limited Discoverable Mode flag to be set in the primary
advertisement and The LE General Discoverable Mode flag will not be set.
The LE Limited Discoverable Mode flag will automatically turn off after [seconds] discoverable [on] must
be set to use this feature.
Entering the command by itself will show the current value set.
Usage#discoverable-timeout[seconds]tx-power
Show/Enable/Disable TX power to be advertised.
This sets the TX Power Level field in the advertising packet.
The value is in dBm and can be between -127 and 127.
When this feature is turned on the LE device will advertise its transmit power in the primary
advertisement.
This feature can be modified while advertising.
Entering the command by itself will show the current value set.
Usage#tx-power[on/off][power]name
Configure local name to be advertised.
Local name to be used in the advertising report.
If the string is too big to fit into the packet it will be truncated.
It will either advertise as a complete local name or if it has to be truncated then a shortened local
name.
Usage#name[on/off/name]Example#name"0123456789abcdef0123456789abcdef"appearance
Configure custom appearance to be advertised.
Usage#appearance[on/off/value]duration
Set/Get advertise duration.
The Duration parameter configures the length of an Instance.
The value is in seconds.
A value of 0 indicates a default value is chosen for the Duration.
The default is 2 seconds.
If only one advertising Instance has been added, then the Duration value will be ignored.
If multiple advertising Instances have been added, then the Duration value will be used to determine the
length of time each Instance is advertised for.
The Duration value is used to calculate the number of advertising events that will be used to advertise
each Instance.
The number of advertising events is calculated by dividing the Duration value by the advertising
interval.
The advertising interval is determined by the advertising parameters that are set for each Instance. The
advertising interval is the maximum of the advertising intervals set for each Instance.
Usage#duration[seconds]timeout
Set/Get advertise timeout.
Usage#timeout[seconds]secondary
Set/Get advertise secondary channel.
Usage#secondary[1M/2M/Coded]interval
Set/Get advertise interval.
The Interval parameter configures the advertising interval of an Instance.
The value is in milliseconds.
A value of 0 indicates a default value is chosen for the Interval.
The default is 100 milliseconds.
The Interval value is used to calculate the number of advertising events that will be used to advertise
each Instance.
The number of advertising events is calculated by dividing the Duration value by the advertising
interval.
The advertising interval is determined by the advertising parameters that are set for each Instance.
The advertising interval is the maximum of the advertising intervals set for each Instance.
Usage#interval[milliseconds]clear
Clear advertise config.
This will stop advertising if it is currently advertising.
If you want to change the advertise configuration while advertising you must first clear the advertise
configuration and then set the new advertise configuration.
Usage#clear[uuids/service/manufacturer/config-name...]
Install Now
PNG Icons
SVG Icons