A message bus daemon has a configuration file that specializes it for a particular application. For
example, one configuration file might set up the message bus to be a systemwide message bus, while
another might set it up to be a per-user-login-session bus.
The configuration file also establishes resource limits, security parameters, and so forth.
The configuration file is not part of any interoperability specification and its backward compatibility
is not guaranteed; this document is documentation, not specification.
The standard systemwide and per-session message bus setups are configured in the files
"/usr/share/dbus-1/system.conf" and "/usr/share/dbus-1/session.conf". These files normally <include> a
system-local.conf or session-local.conf in /etc/dbus-1; you can put local overrides in those files to
avoid modifying the primary configuration files.
The standard system bus normally reads additional XML files from /usr/share/dbus-1/system.d. Third-party
packages should install the default policies necessary for correct operation into that directory, which
has been supported since dbus 1.10 (released in 2015).
The standard system bus normally also reads XML files from /etc/dbus-1/system.d, which should be used by
system administrators if they wish to override default policies.
Third-party packages would historically install XML files into /etc/dbus-1/system.d, but this practice is
now considered to be deprecated: that directory should be treated as reserved for the system
administrator.
The configuration file is an XML document. It must have the following doctype declaration:
<!DOCTYPE busconfig PUBLIC "-//freedesktop//DTD D-Bus Bus Configuration 1.0//EN"
"http://www.freedesktop.org/standards/dbus/1.0/busconfig.dtd">
The following elements may be present in the configuration file.
• <busconfig>
Root element.
• <type>
The well-known type of the message bus. Currently known values are "system" and "session"; if other
values are set, they should be either added to the D-Bus specification, or namespaced. The last <type>
element "wins" (previous values are ignored). This element only controls which message bus specific
environment variables are set in activated clients. Most of the policy that distinguishes a session bus
from the system bus is controlled from the other elements in the configuration file.
If the well-known type of the message bus is "session", then the DBUS_STARTER_BUS_TYPE environment
variable will be set to "session" and the DBUS_SESSION_BUS_ADDRESS environment variable will be set to
the address of the session bus. Likewise, if the type of the message bus is "system", then the
DBUS_STARTER_BUS_TYPE environment variable will be set to "system" and the DBUS_SYSTEM_BUS_ADDRESS
environment variable will be set to the address of the system bus (which is normally well known anyway).
Example: <type>session</type>
• <include>
Include a file <include>filename.conf</include> at this point. If the filename is relative, it is located
relative to the configuration file doing the including.
<include> has an optional attribute "ignore_missing=(yes|no)" which defaults to "no" if not provided.
This attribute controls whether it's a fatal error for the included file to be absent.
• <includedir>
Include all files in <includedir>foo.d</includedir> at this point. Files in the directory are included in
undefined order. Only files ending in ".conf" are included.
This is intended to allow extension of the system bus by particular packages. For example, if CUPS wants
to be able to send out notification of printer queue changes, it could install a file to
/usr/share/dbus-1/system.d that allowed all apps to receive this message and allowed the printer daemon
user to send it.
• <user>
The user account the daemon should run as, as either a username or a UID. If the daemon cannot change to
this UID on startup, it will exit. If this element is not present, the daemon will not change or care
about its UID.
The last <user> entry in the file "wins", the others are ignored.
The user is changed after the bus has completed initialization. So sockets etc. will be created before
changing user, but no data will be read from clients before changing user. This means that sockets and
PID files can be created in a location that requires root privileges for writing.
• <fork>
If present, the bus daemon becomes a real daemon (forks into the background, etc.). This is generally
used rather than the --fork command line option.
• <keep_umask>
If present, the bus daemon keeps its original umask when forking. This may be useful to avoid affecting
the behavior of child processes.
• <syslog>
If present, the bus daemon will log to syslog. The --syslog, --syslog-only and --nosyslog command-line
options take precedence over this setting.
• <pidfile>
If present, the bus daemon will write its pid to the specified file. The --nopidfile command-line option
takes precedence over this setting.
• <allow_anonymous>
If present, connections that authenticated using the ANONYMOUS mechanism will be authorized to connect.
This option has no practical effect unless the ANONYMOUS mechanism has also been enabled using the <auth>
element, described below.
Using this directive in the configuration of the well-known system bus or the well-known session bus will
make that bus insecure and should never be done. Similarly, on custom bus types, using this directive
will usually make the custom bus insecure, unless its configuration has been specifically designed to
prevent anonymous users from causing damage or escalating privileges.
• <listen>
Add an address that the bus should listen on. The address is in the standard D-Bus format that contains a
transport name plus possible parameters/options.
On platforms other than Windows, unix-based transports (unix, systemd, launchd) are the default for both
the well-known system bus and the well-known session bus, and are strongly recommended.
On Windows, unix-based transports are not available, so TCP-based transports must be used. Similar to
remote X11, the tcp and nonce-tcp transports have no integrity or confidentiality protection, so they
should normally only be used across the local loopback interface, for example using an address like
tcp:host=127.0.0.1 or nonce-tcp:host=localhost. In particular, configuring the well-known system bus or
the well-known session bus to listen on a non-loopback TCP address is insecure.
Developers are sometimes tempted to use remote TCP as a debugging tool. However, if this functionality is
left enabled in finished products, the result will be dangerously insecure. Instead of using remote TCP,
developers should relayconnectionsviaSecureShellorasimilarprotocol[1].
Remote TCP connections were historically sometimes used to share a single session bus between login
sessions of the same user on different machines within a trusted local area network, in conjunction with
unencrypted remote X11, a NFS-shared home directory and NIS (YP) authentication. This is insecure against
an attacker on the same LAN and should be considered strongly deprecated; more specifically, it is
insecure in the same ways and for the same reasons as unencrypted remote X11 and NFSv2/NFSv3. The D-Bus
maintainers recommend using a separate session bus per (user, machine) pair, only accessible from within
that machine.
Example: <listen>unix:path=/tmp/foo</listen>
Example: <listen>tcp:host=localhost,port=1234</listen>
If there are multiple <listen> elements, then the bus listens on multiple addresses. The bus will pass
its address to started services or other interested parties with the last address given in <listen>
first. That is, apps will try to connect to the last <listen> address first.
tcp sockets can accept IPv4 addresses, IPv6 addresses or hostnames. If a hostname resolves to multiple
addresses, the server will bind to all of them. The family=ipv4 or family=ipv6 options can be used to
force it to bind to a subset of addresses
Example: <listen>tcp:host=localhost,port=0,family=ipv4</listen>
A special case is using a port number of zero (or omitting the port), which means to choose an available
port selected by the operating system. The port number chosen can be obtained with the --print-address
command line parameter and will be present in other cases where the server reports its own address, such
as when DBUS_SESSION_BUS_ADDRESS is set.
Example: <listen>tcp:host=localhost,port=0</listen>
tcp/nonce-tcp addresses also allow a bind=hostname option, used in a listenable address to configure the
interface on which the server will listen: either the hostname is the IP address of one of the local
machine's interfaces (most commonly 127.0.0.1), a DNS name that resolves to one of those IP addresses,
'0.0.0.0' to listen on all IPv4 interfaces simultaneously, or '::' to listen on all IPv4 and IPv6
interfaces simultaneously (if supported by the OS). If not specified, the default is the same value as
"host".
Example: <listen>tcp:host=localhost,bind=0.0.0.0,port=0</listen>
• <auth>
Lists permitted authorization mechanisms. If this element doesn't exist, then all known mechanisms are
allowed. If there are multiple <auth> elements, all the listed mechanisms are allowed. The order in which
mechanisms are listed is not meaningful.
On non-Windows operating systems, allowing only the EXTERNAL authentication mechanism is strongly
recommended. This is the default for the well-known system bus and for the well-known session bus.
Example: <auth>EXTERNAL</auth>
Example: <auth>DBUS_COOKIE_SHA1</auth>
• <servicedir>
Adds a directory to search for .service files, which tell the dbus-daemon how to start a program to
provide a particular well-known bus name. See the D-Bus Specification for more details about the contents
of .service files.
If a particular service is found in more than one <servicedir>, the first directory listed in the
configuration file takes precedence. If two service files providing the same well-known bus name are
found in the same directory, it is arbitrary which one will be chosen (this can only happen if at least
one of the service files does not have the recommended name, which is its well-known bus name followed by
".service").
• <standard_session_servicedirs/>
<standard_session_servicedirs/> requests a standard set of session service directories. Its effect is
similar to specifying a series of <servicedir/> elements for each of the data directories, in the order
given here. It is not exactly equivalent, because there is currently no way to disable directory
monitoring or enforce strict service file naming for a <servicedir/>.
As with <servicedir/> elements, if a particular service is found in more than one service directory, the
first directory takes precedence. If two service files providing the same well-known bus name are found
in the same directory, it is arbitrary which one will be chosen (this can only happen if at least one of
the service files does not have the recommended name, which is its well-known bus name followed by
".service").
On Unix, the standard session service directories are:
• $XDG_RUNTIME_DIR/dbus-1/services, if XDG_RUNTIME_DIR is set (see the XDG Base Directory Specification
for details of XDG_RUNTIME_DIR): this location is suitable for transient services created at runtime
by systemd generators (see systemd.generator(7)), session managers or other session infrastructure.
It is an extension provided by the reference implementation of dbus-daemon, and is not standardized
in the D-Bus Specification.
Unlike the other standard session service directories, this directory enforces strict naming for the
service files: the filename must be exactly the well-known bus name of the service, followed by
".service".
Also unlike the other standard session service directories, this directory is never monitored with
inotify(7) or similar APIs. Programs that create service files in this directory while a dbus-daemon
is running are expected to call the dbus-daemon's ReloadConfig() method after they have made changes.
• $XDG_DATA_HOME/dbus-1/services, where XDG_DATA_HOME defaults to ~/.local/share (see the XDG Base
Directory Specification): this location is specified by the D-Bus Specification, and is suitable for
per-user, locally-installed software.
• directory/dbus-1/services for each directory in XDG_DATA_DIRS, where XDG_DATA_DIRS defaults to
/usr/local/share:/usr/share (see the XDG Base Directory Specification): these locations are specified
by the D-Bus Specification. The defaults are suitable for software installed locally by a system
administrator (/usr/local/share) or for software installed from operating system packages
(/usr/share). Per-user or system-wide configuration that sets the XDG_DATA_DIRS environment variable
can extend this search path to cover installations in other locations, for example
~/.local/share/flatpak/exports/share/ and /var/lib/flatpak/exports/share/ when flatpak(1) is used.
• ${datadir}/dbus-1/services for the ${datadir} that was specified when dbus was compiled, typically
/usr/share: this location is an extension provided by the reference dbus-daemon implementation, and
is suitable for software stacks installed alongside dbus-daemon.
The "XDG Base Directory Specification" can be found at http://freedesktop.org/wiki/Standards/basedir-spec
if it hasn't moved, otherwise try your favorite search engine.
On Windows, the standard session service directories are:
• %CommonProgramFiles%/dbus-1/services if %CommonProgramFiles% is set: this location is suitable for
system-wide installed software packages
• A share/dbus-1/services directory found in the same directory hierarchy (prefix) as the dbus-daemon:
this location is suitable for software stacks installed alongside dbus-daemon
The <standard_session_servicedirs/> option is only relevant to the per-user-session bus daemon defined in
/etc/dbus-1/session.conf. Putting it in any other configuration file would probably be nonsense.
• <standard_system_servicedirs/>
<standard_system_servicedirs/> specifies the standard system-wide activation directories that should be
searched for service files. As with session services, the first directory listed has highest precedence.
On Unix, the standard system service directories are:
• /etc/dbus-1/system-services: this location is specified by the D-Bus Specification, and is suitable
for software installed locally by the system administrator, or by an asset manager deploying services
that are not part of the OS (perhaps while /usr/ is read-only)
• /run/dbus-1/system-services: this location is specified by the D-Bus Specification, and is suitable
for ephemeral services that will disappear after a reboot
• /usr/local/share/dbus-1/system-services: this location is specified by the D-Bus Specification, and
is suitable for software installed locally by the system administrator
• /usr/share/dbus-1/system-services: this location is specified by the D-Bus Specification, and is
suitable for software installed by operating system packages
• ${datadir}/dbus-1/system-services for the ${datadir} that was specified when dbus was compiled,
typically /usr/share: this location is an extension provided by the reference dbus-daemon
implementation, and is suitable for software stacks installed alongside dbus-daemon
• /lib/dbus-1/system-services: this location is specified by the D-Bus Specification, and was intended
for software installed by operating system packages and used during early boot (but it should be
considered deprecated, because the reference dbus-daemon is not designed to be available during early
boot)
On Windows, there is no standard system bus, so there are no standard system bus directories either.
The <standard_system_servicedirs/> option is only relevant to the per-system bus daemon defined in
/usr/share/dbus-1/system.conf. Putting it in any other configuration file would probably be nonsense.
• <servicehelper/>
<servicehelper/> specifies the setuid helper that is used to launch system daemons with an alternate
user. Typically this should be the dbus-daemon-launch-helper executable in located in libexec.
The <servicehelper/> option is only relevant to the per-system bus daemon defined in
/usr/share/dbus-1/system.conf. Putting it in any other configuration file would probably be nonsense.
• <limit>
<limit> establishes a resource limit. For example:
<limit name="max_message_size">64</limit>
<limit name="max_completed_connections">512</limit>
The name attribute is mandatory. Available limit names are:
"max_incoming_bytes" : total size in bytes of messages
incoming from a single connection
"max_incoming_unix_fds" : total number of unix fds of messages
incoming from a single connection
"max_outgoing_bytes" : total size in bytes of messages
queued up for a single connection
"max_outgoing_unix_fds" : total number of unix fds of messages
queued up for a single connection
"max_message_size" : max size of a single message in
bytes
"max_message_unix_fds" : max unix fds of a single message
"service_start_timeout" : milliseconds (thousandths) until
a started service has to connect
"auth_timeout" : milliseconds (thousandths) a
connection is given to
authenticate
"pending_fd_timeout" : milliseconds (thousandths) a
fd is given to be transmitted to
dbus-daemon before disconnecting the
connection
"max_completed_connections" : max number of authenticated connections
"max_incomplete_connections" : max number of unauthenticated
connections
"max_connections_per_user" : max number of completed connections from
the same user (only enforced on Unix OSs)
"max_pending_service_starts" : max number of service launches in
progress at the same time
"max_names_per_connection" : max number of names a single
connection can own
"max_match_rules_per_connection": max number of match rules for a single
connection
"max_replies_per_connection" : max number of pending method
replies per connection
(number of calls-in-progress)
"reply_timeout" : milliseconds (thousandths)
until a method call times out
The max incoming/outgoing queue sizes allow a new message to be queued if one byte remains below the max.
So you can in fact exceed the max by max_message_size.
max_completed_connections divided by max_connections_per_user is the number of users that can work
together to denial-of-service all other users by using up all connections on the systemwide bus.
Limits are normally only of interest on the systemwide bus, not the user session buses.
• <policy>
The <policy> element defines a security policy to be applied to a particular set of connections to the
bus. A policy is made up of <allow> and <deny> elements. Policies are normally used with the systemwide
bus; they are analogous to a firewall in that they allow expected traffic and prevent unexpected traffic.
Currently, the system bus has a default-deny policy for sending method calls and owning bus names, and a
default-allow policy for receiving messages, sending signals, and sending a single success or error reply
for each method call that does not have the NO_REPLY flag. Sending more than the expected number of
replies is not allowed.
In general, it is best to keep system services as small, targeted programs which run in their own process
and provide a single bus name. Then, all that is needed is an <allow> rule for the "own" permission to
let the process claim the bus name, and a "send_destination" rule to allow traffic from some or all uids
to your service.
The <policy> element has one of four attributes:
context="(default|mandatory)"
at_console="(true|false)"
user="username or userid"
group="group name or gid"
Policies are applied to a connection as follows:
- all context="default" policies are applied
- all group="connection's user's group" policies are applied
in undefined order
- all user="connection's auth user" policies are applied
in undefined order
- all at_console="true" policies are applied
- all at_console="false" policies are applied
- all context="mandatory" policies are applied
Policies applied later will override those applied earlier, when the policies overlap. Multiple policies
with the same user/group/context are applied in the order they appear in the config file.
<deny><allow>
A <deny> element appears below a <policy> element and prohibits some action. The <allow> element makes an
exception to previous <deny> statements, and works just like <deny> but with the inverse meaning.
The possible attributes of these elements are:
send_interface="interface_name" | "*"
send_member="method_or_signal_name" | "*"
send_error="error_name" | "*"
send_broadcast="true" | "false"
send_destination="name" | "*"
send_destination_prefix="name"
send_type="method_call" | "method_return" | "signal" | "error" | "*"
send_path="/path/name" | "*"
receive_interface="interface_name" | "*"
receive_member="method_or_signal_name" | "*"
receive_error="error_name" | "*"
receive_sender="name" | "*"
receive_type="method_call" | "method_return" | "signal" | "error" | "*"
receive_path="/path/name" | "*"
send_requested_reply="true" | "false"
receive_requested_reply="true" | "false"
eavesdrop="true" | "false"
own="name" | "*"
own_prefix="name"
user="username" | "*"
group="groupname" | "*"
Examples:
<deny send_destination="org.freedesktop.Service" send_interface="org.freedesktop.System" send_member="Reboot"/>
<deny send_destination="org.freedesktop.System"/>
<deny receive_sender="org.freedesktop.System"/>
<deny user="john"/>
<deny group="enemies"/>
The <deny> element's attributes determine whether the deny "matches" a particular action. If it matches,
the action is denied (unless later rules in the config file allow it).
Rules with one or more of the send_* family of attributes are checked in order when a connection attempts
to send a message. The last rule that matches the message determines whether it may be sent. The
well-known session bus normally allows sending any message. The well-known system bus normally allows
sending any signal, selected method calls to the dbus-daemon, and exactly one reply to each
previously-sent method call (either success or an error). Either of these can be overridden by
configuration; on the system bus, services that will receive method calls must install configuration that
allows them to do so, usually via rules of the form <policy context="default"><allow
send_destination="..."/><policy>.
Rules with one or more of the receive_* family of attributes, or with the eavesdrop attribute and no
others, are checked for each recipient of a message (there might be more than one recipient if the
message is a broadcast or a connection is eavesdropping). The last rule that matches the message
determines whether it may be received. The well-known session bus normally allows receiving any message,
including eavesdropping. The well-known system bus normally allows receiving any message that was not
eavesdropped (any unicast message addressed to the recipient, and any broadcast message).
The eavesdrop, min_fds and max_fds attributes are modifiers that can be applied to either send_* or
receive_* rules, and are documented below.
send_destination and receive_sender rules mean that messages may not be sent to or received from the
*owner* of the given name, not that they may not be sent *to that name*. That is, if a connection owns
services A, B, C, and sending to A is denied, sending to B or C will not work either. As a special case,
send_destination="*" matches any message (whether it has a destination specified or not), and
receive_sender="*" similarly matches any message.
A send_destination_prefix rule opens or closes the whole namespace for sending. It means that messages
may or may not be sent to the owner of any name matching the prefix, regardless of whether it is the
primary or the queued owner. In other words, for <allow send_destination_prefix="a.b"/> rule and names
"a.b", "a.b.c", and "a.b.c.d" present on the bus, it works the same as if three separate rules: <allow
send_destination="a.b"/>, <allow send_destination="a.b.c"/>, and <allow send_destination="a.b.c.d"/> had
been defined. The rules for matching names are the same as in own_prefix (see below): a prefix of "a.b"
matches names "a.b" or "a.b.c" or "a.b.c.d", but not "a.bc" or "a.c". The send_destination_prefix
attribute cannot be combined with the send_destination attribute in the same rule.
Rules with send_broadcast="true" match signal messages with no destination (broadcasts). Rules with
send_broadcast="false" are the inverse: they match any unicast destination (unicast signals, together
with all method calls, replies and errors) but do not match messages with no destination (broadcasts).
This is not the same as send_destination="*", which matches any sent message, regardless of whether it
has a destination or not.
The other send_* and receive_* attributes are purely textual/by-value matches against the given field in
the message header, except that for the attributes where it is allowed, * matches any message (whether it
has the relevant header field or not). For example, send_interface="*" matches any sent message, even if
it does not contain an interface header field. More complex glob matching such as foo.bar.* is not
allowed.
"Eavesdropping" occurs when an application receives a message that was explicitly addressed to a name the
application does not own, or is a reply to such a message. Eavesdropping thus only applies to messages
that are addressed to services and replies to such messages (i.e. it does not apply to signals).
For <allow>, eavesdrop="true" indicates that the rule matches even when eavesdropping. eavesdrop="false"
is the default and means that the rule only allows messages to go to their specified recipient. For
<deny>, eavesdrop="true" indicates that the rule matches only when eavesdropping. eavesdrop="false" is
the default for <deny> also, but here it means that the rule applies always, even when not eavesdropping.
The eavesdrop attribute can only be combined with send and receive rules (with send_* and receive_*
attributes).
The [send|receive]_requested_reply attribute works similarly to the eavesdrop attribute. It controls
whether the <deny> or <allow> matches a reply that is expected (corresponds to a previous method call
message). This attribute only makes sense for reply messages (errors and method returns), and is ignored
for other message types.
For <allow>, [send|receive]_requested_reply="true" is the default and indicates that only requested
replies are allowed by the rule. [send|receive]_requested_reply="false" means that the rule allows any
reply even if unexpected.
For <deny>, [send|receive]_requested_reply="false" is the default but indicates that the rule matches
only when the reply was not requested. [send|receive]_requested_reply="true" indicates that the rule
applies always, regardless of pending reply state.
The min_fds and max_fds attributes modify either send_* or receive_* rules. A rule with the min_fds
attribute only matches messages if they have at least that many Unix file descriptors attached.
Conversely, a rule with the max_fds attribute only matches messages if they have no more than that many
file descriptors attached. In practice, rules with these attributes will most commonly take the form
<allow send_destination="..." max_fds="0"/>, <deny send_destination="..." min_fds="1"/> or <deny
receive_sender="*" min_fds="1"/>.
Rules with the user or group attribute are checked when a new connection to the message bus is
established, and control whether the connection can continue. Each of these attributes cannot be combined
with any other attribute. As a special case, both user="*" and group="*" match any connection. If there
are no rules of this form, the default is to allow connections from the same user ID that owns the
dbus-daemon process. The well-known session bus normally uses that default behaviour, while the
well-known system bus normally allows any connection.
Rules with the own or own_prefix attribute are checked when a connection attempts to own a well-known bus
names. As a special case, own="*" matches any well-known bus name. The well-known session bus normally
allows any connection to own any name, while the well-known system bus normally does not allow any
connection to own any name, except where allowed by further configuration. System services that will own
a name must install configuration that allows them to do so, usually via rules of the form <policy
user="some-system-user"><allow own="..."/></policy>.
<allow own_prefix="a.b"/> allows you to own the name "a.b" or any name whose first dot-separated elements
are "a.b": in particular, you can own "a.b.c" or "a.b.c.d", but not "a.bc" or "a.c". This is useful when
services like Telepathy and ReserveDevice define a meaning for subtrees of well-known names, such as
org.freedesktop.Telepathy.ConnectionManager.(anything) and org.freedesktop.ReserveDevice1.(anything).
It does not make sense to deny a user or group inside a <policy> for a user or group; user/group denials
can only be inside context="default" or context="mandatory" policies.
A single <deny> rule may specify combinations of attributes such as send_destination and send_interface
and send_type. In this case, the denial applies only if both attributes match the message being denied.
e.g. <deny send_interface="foo.bar" send_destination="foo.blah"/> would deny messages with the given
interface AND the given bus name. To get an OR effect you specify multiple <deny> rules.
You can't include both send_ and receive_ attributes on the same rule, since "whether the message can be
sent" and "whether it can be received" are evaluated separately.
Be careful with send_interface/receive_interface, because the interface field in messages is optional. In
particular, do NOT specify <deny send_interface="org.foo.Bar"/>! This will cause no-interface messages to
be blocked for all services, which is almost certainly not what you intended. Always use rules of the
form: <deny send_interface="org.foo.Bar" send_destination="org.foo.Service"/>
• <selinux>
The <selinux> element contains settings related to Security Enhanced Linux. More details below.
• <associate>
An <associate> element appears below an <selinux> element and creates a mapping. Right now only one kind
of association is possible:
<associate own="org.freedesktop.Foobar" context="foo_t"/>
This means that if a connection asks to own the name "org.freedesktop.Foobar" then the source context
will be the context of the connection and the target context will be "foo_t" - see the short discussion
of SELinux below.
Note, the context here is the target context when requesting a name, NOT the context of the connection
owning the name.
There's currently no way to set a default for owning any name, if we add this syntax it will look like:
<associate own="*" context="foo_t"/>
If you find a reason this is useful, let the developers know. Right now the default will be the security
context of the bus itself.
If two <associate> elements specify the same name, the element appearing later in the configuration file
will be used.
• <apparmor>
The <apparmor> element is used to configure AppArmor mediation on the bus. It can contain one attribute
that specifies the mediation mode:
<apparmor mode="(enabled|disabled|required)"/>
The default mode is "enabled". In "enabled" mode, AppArmor mediation will be performed if AppArmor
support is available in the kernel. If it is not available, dbus-daemon will start but AppArmor mediation
will not occur. In "disabled" mode, AppArmor mediation is disabled. In "required" mode, AppArmor
mediation will be enabled if AppArmor support is available, otherwise dbus-daemon will refuse to start.
The AppArmor mediation mode of the bus cannot be changed after the bus starts. Modifying the mode in the
configuration file and sending a SIGHUP signal to the daemon has no effect on the mediation mode.
Install Now
PNG Icons
