NormalOptions
These are the options used to select the parameters of a print job that are usually controlled on a per
job basis.
-bbits
Number of bits per plane (1 or 2) [1].
-c Print in color (else monochrome).
-dduplex
Duplex code to send to printer [1].
│ │ │
│ 1 off │ 2 long edge │ 3 short edge
-mmedia
Media code to send to printer [1].
─────────────────────────────────────
Media HP CLJ 1500 KM-1635
-z0 -z1
─────────────────────────────────────
autoselect 0 0
plain 1 1
preprinted 2 2
letterhead 3 3
transparency 4 4
prepunched 5 5
labels 6 6
bond 7 7
recycled 8 8
color 9 9
cardstock 10 10
envelope 11 11
light 13 na
tough 14 na
vellum na 15
rough na 16
thick na 19
highqual na 20
-ppaper
Paper size code to send to printer [1].
┌──────────────────┬─────────────────┐
│ 1 letter │ 3 ledger │
│ 5 legal │ 6 statement │
│ 7 executive │ 8 A3 │
│ 9 A4 │ 11 A5 │
│ 12 B4 │ 13 B5jis │
│ 14 folio │ 19 env9 │
│ 20 env10 │ 27 envDL │
│ 28 envC5 │ 30 envC4 │
│ 37 envMonarch │ 257 A6 │
│ 258 B6 │ 259 B5iso │
│ 260 env6 │ │
└──────────────────┴─────────────────┘
-ncopies
Number of copies [1].
-rxresxyres
Set device resolution in pixels/inch [600x600].
-ssource
Source (Input Slot) code to send to printer [7].
│ │
│ 1 tray1 │ 2 tray2
│ 4 manual │ 7 auto
-2-3-4-5-6-8-9-10-12-14-15-16-18
Print in N-up. Requires the psutils package.
-oorient
Orientation used for N-up.
Portrait -op (normal)
Landscape -ol (rotated 90 degrees anticlockwise)
Seascape -os (rotated 90 degrees clockwise)
PrinterTweakingOptions
These are the options used to customize the operation of foo2oak for a particular printer.
-uxoffxyoff
Set the offset of the start of the printable region from the upper left corner, in pixels [varies
with paper size]. The defaults should work on the 2200DL and 2300DL, and have not been tested on
any other printers.
-lxoffxyoff
Set the offset of the end of the printable region from the lower right corner, in pixels [varies
with paper size]. The defaults should work on the 2200DL and 2300DL, and have not been tested on
any other printers.
-Lmask
Send the logical clipping values from -u/-l in the OAKT stream. foo2oak-wrapper always runs
Ghostscript with the ideal page dimensions, so that the scale of the image is correct, regardless
whether or not the printer has unprintable regions. This option is used to move the position of
the clipped image back to where it belongs on the page. The default is to send the amount which
was clipped by -u and -l, and should be good in most cases.
0 don't send any logical clipping amounts
1 only send Y clipping amount
2 only send X clipping amount
3 send both X and Y clipping amounts
-zmodel
Model is 0 for the HP Color LaserJet 1500, and 1 for the Kyocera KM-1635/KM-2035 copiers. The
default is 0.
ColorTweakingOptions
These are the options used to control the quality of color output. Color correction is currently a WORK
IN PROGRESS.
-ggsopts
Additional options to pass to Ghostscript, such as -g“-dDITHERPPI=nnn”, etc. This option may
appear more than once.
-Gprofile.icm
Convert profile.icm to a Postscript color rendering dictionary (CRD) using foo2zjs-icc2ps and
adjust the printer colors by using the Postscript setcolorrendering operator. (WORK IN PROGRESS).
-Ggamma-file.ps
Prepend gamma-file.ps to the Postscript input to perform color correction using the
setcolortransfer Postscript operator. For example, the file might contain:
{0.333 exp} {0.333 exp} {0.333 exp} {0.333 exp} setcolortransfer
-Iintent
Select profile intent from the ICM file. 0=Perceptual, 1=Colorimetric, 2=Saturation, 3=Absolute.
Default is 0 (perceptual).
DebuggingOptions
These options are used for debugging foo2oak and its wrapper.
-Splane
Output just a single color plane from a color print and print it on the black plane. The default
is to output all color planes.
1 Cyan
2 Magenta
3 Yellow
4 Black
-Dlevel
Set Debug level [0].
Install Now
Emojis
PNG Icons
