NormalOptions
These are the options used to select the parameters of a print job that are usually controlled on a per
job basis.
-c Print in color (else monochrome).
-Ccolormode
Color correction mode [0].
1 CRD
10 ICM color profile (using -G *.icm file)
-dduplex
Duplex code to send to printer [1].
│ │ │
│ 1 off │ 2 long edge │ 3 short edge
-mmedia
Media code to send to printer [0].
────────────────────────
Media QPDL
────────────────────────
plain 0
thick 1
thin 2
bond 3
color 4
card 5
labels 6
envelope 7
preprinted 8
cotton 9
recycled 10
transparency 11
archive 12
-ppaper
Paper size code to send to printer [0].
┌───────────────┬──────────────────┐
│ 0 letter │ 1 legal │
│ 2 A4 │ 3 executive │
│ 6 env #10 │ 7 env Monarch │
│ 8 env C5 │ 9 env DL │
│ 11 B5jis │ 12 B5iso │
│ 16 A5 │ 17 A6 │
│ 23 env C6 │ 24 folio │
│ 25 env 6.75 │ 26 env #9 │
│ 28 oficio │ │
└───────────────┴──────────────────┘
-ncopies
Number of copies [1].
-rxresxyres
Set device resolution in pixels/inch [1200x600].
-ssource
Source (Input Slot) code to send to printer [255].
│ │
│ 1 auto │ 2 manual
│ 3 multi │ 4 tray1
-t Draft mode. Every other pixel is white.
-2-3-4-5-6-8-9-10-12-14-15-16-18
Print in N-up. Requires the psutils package.
-oorient
Orientation used for N-up.
Portrait -op (normal)
Landscape -ol (rotated 90 degrees anticlockwise)
Seascape -os (rotated 90 degrees clockwise)
PrinterTweakingOptions
These are the options used to customize the operation of foo2qpdl for a particular printer.
-uxoffxyoff
Set the offset of the start of the printable region from the upper left corner, in pixels [varies
with paper size].
-lxoffxyoff
Set the offset of the end of the printable region from the lower right corner, in pixels [varies
with paper size].
-Lmask
Send the logical clipping values from -u/-l in the QPDL stream. foo2qpdl-wrapper always runs
Ghostscript with the ideal page dimensions, so that the scale of the image is correct, regardless
whether or not the printer has unprintable regions. This option is used to move the position of
the clipped image back to where it belongs on the page. The default is to send the amount which
was clipped by -u and -l, and should be good in most cases.
0 don't send any logical clipping amounts
1 only send Y clipping amount
2 only send X clipping amount
3 send both X and Y clipping amounts
-zmodel
Printer model. Model 0 is the default.
model Description
0 CLP-300, CLX-2160, CLX-3160
1 CLP-600
2 CLP-310, CLP-315, CLP-610, CLX-3175
3 CLP-620, CLP-360, CLP-365
ColorTweakingOptions
These are the options used to control the quality of color output. Color correction is currently a WORK
IN PROGRESS.
-aparm=val
Color Adjust. parm is b, c, s, cr, mg, yb for brightness, contrast, saturation, cyan-red balance,
magenta-green balance, and yellow-blue balance. val is 0 to 100. Multiple options are allowed.
The default is "-ab=50 -ac=50 -as=50 -acr=50 -amg=50 -ayb=50". This only works when the -z3 (e.g.
CLP-365) model is set!
-ggsopts
Additional options to pass to Ghostscript, such as -g“-dDITHERPPI=nnn”, etc. This option may
appear more than once.
-Gprofile.icm
Convert profile.icm to a Postscript color rendering dictionary (CRD) using foo2zjs-icc2ps and
adjust the printer colors by using the Postscript setcolorrendering operator. (WORK IN PROGRESS).
-Ggamma-file.ps
Prepend gamma-file.ps to the Postscript input to perform color correction using the
setcolortransfer Postscript operator. For example, the file might contain:
{0.333 exp} {0.333 exp} {0.333 exp} {0.333 exp} setcolortransfer
-Iintent
Select profile intent from the ICM file. 0=Perceptual, 1=Colorimetric, 2=Saturation, 3=Absolute.
Default is 0 (perceptual).
DebuggingOptions
These options are used for debugging foo2qpdl and its wrapper.
-Splane
Output just a single color plane from a color print and print it on the black plane. The default
is to output all color planes.
1 Cyan
2 Magenta
3 Yellow
4 Black
-Dlevel
Set Debug level [0].
Install Now
Emojis
PNG Icons
