ifmt=<in-format>
Specifies the format of the input table as specified by parameter in. The known formats are listed
in SUN/256. This flag can be used if you know what format your table is in. If it has the special
value (auto) (the default), then an attempt will be made to detect the format of the table auto‐
matically. This cannot always be done correctly however, in which case the program will exit with
an error explaining which formats were attempted. This parameter is ignored for scheme-specified
tables.
istream=true|false
If set true, the input table specified by the in parameter will be read as a stream. It is neces‐
sary to give the ifmt parameter in this case. Depending on the required operations and processing
mode, this may cause the read to fail (sometimes it is necessary to read the table more than
once). It is not normally necessary to set this flag; in most cases the data will be streamed au‐
tomatically if that is the best thing to do. However it can sometimes result in less resource us‐
age when processing large files in certain formats (such as VOTable). This parameter is ignored
for scheme-specified tables.
in=<table>
The location of the input table. This may take one of the following forms:
* A filename.
* A URL.
* The special value "-", meaning standard input. In this case the input format must be given ex‐
plicitly using the ifmt parameter. Note that not all formats can be streamed in this way.
* A scheme specification of the form :<scheme-name>:<scheme-args>.
* A system command line with either a "<" character at the start, or a "|" character at the end
("<syscmd" or "syscmd|"). This executes the given pipeline and reads from its standard output.
This will probably only work on unix-like systems.
In any case, compressed data in one of the supported compression formats (gzip, Unix compress or
bzip2) will be decompressed transparently.
cmd=<cmds>
Specifies processing to be performed on the input table as specified by parameter in, before any
other processing has taken place. The value of this parameter is one or more of the filter com‐
mands described in SUN/256. If more than one is given, they must be separated by semicolon charac‐
ters (";"). This parameter can be repeated multiple times on the same command line to build up a
list of processing steps. The sequence of commands given in this way defines the processing
pipeline which is performed on the table.
Commands may alternatively be supplied in an external file, by using the indirection character
'@'. Thus a value of "@filename" causes the file filename to be read for a list of filter commands
to execute. The commands in the file may be separated by newline characters and/or semicolons, and
lines which are blank or which start with a '#' character are ignored. A backslash character '\fR'attheendofalinejoinsitwiththefollowingline.omode=out|meta|stats|count|checksum|cgi|discard|topcat|samp|tosql|gui
The mode in which the result table will be output. The default mode is out, which means that the
result will be written as a new table to disk or elsewhere, as determined by the out and ofmt pa‐
rameters. However, there are other possibilities, which correspond to uses to which a table can be
put other than outputting it, such as displaying metadata, calculating statistics, or populating a
table in an SQL database. For some values of this parameter, additional parameters (<mode-args>)
are required to determine the exact behaviour.
Possible values are
* out
* meta
* stats
* count
* checksum
* cgi
* discard
* topcat
* samp
* tosql
* gui
Use the help=omode flag or see SUN/256 for more information.
out=<out-table>
The location of the output table. This is usually a filename to write to. If it is equal to the
special value "-" (the default) the output table will be written to standard output.
This parameter must only be given if omode has its default value of "out".
ofmt=<out-format>
Specifies the format in which the output table will be written (one of the ones in SUN/256 -
matching is case-insensitive and you can use just the first few letters). If it has the special
value "(auto)" (the default), then the output filename will be examined to try to guess what sort
of file is required usually by looking at the extension. If it's not obvious from the filename
what output format is intended, an error will result.
This parameter must only be given if omode has its default value of "out".
Install Now
PNG Icons
