pon, poff, plog - starts up, shuts down or lists the log of PPP connections

       The p-commands were written by Christoph Lameter <clameter@debian.org>.  Updated and  revised  by  Philip
       Hands <phil@hands.com>.
       This    manual    was   written   by   Othmar   Pasteka   <othmar@tron.at>.   Modified   by   Rob   Levin
       <lilo@openprojects.net>, with some extensions taken from the old p-commands manual written by John Hasler
       <jhasler@debian.org>.

       This manual page describes the pon, plog and poff scripts, which allow users to control PPP connections.

   ponpon,  invoked  without  arguments,  runs  the  /etc/ppp/ppp_on_boot file, if it exists and is executable.
       Otherwise, a PPP connection will be started using configuration from  /etc/ppp/peers/provider.   This  is
       the default behaviour unless an isp-name argument is given.

       For instance, to use ISP configuration "myisp" run:

              pon myisp

       pon  will then use the options file /etc/ppp/peers/myisp.  You can pass additional pppdoptions after the
       ISP name, too.  pon can be used to run multiple, simultaneous PPP connections.

       pon takes the following command line options:

              -q--quick
                     disconnect when ip-up finishes running.  This function is only available to the root user.

   poffpoff closes a PPP connection. If more than one PPP connection exists, the one named in  the  argument  to
       poff will be killed, e.g.

              poff myprovider2

       will  terminate  the  connection  to  myprovider2, and leave the PPP connections to e.g. "myprovider1" or
       "myprovider3" up and running.

       poff takes the following command line options:

              -r     causes the connection to be redialed after it is dropped.

              -d     toggles the state of pppd's debug option.

              -c     causes pppd(8) to renegotiate compression.

              -a     stops all running ppp connections. If the argument isp-name is given it will be ignored.

              -h     displays help information.

              -v     prints the version and exits.

              If no argument is given, poff will stop or signal pppd  if  and  only  if  there  is  exactly  one
              running. If more than one connection is active, it will exit with an error code of 1.

   plogplog  shows you the last few lines of /var/log/ppp.log. If that file doesn't exist, it shows you the last
       few lines of your /var/log/syslog file, but excluding the lines not generated by pppd.  This script makes
       use of the tail(1) command, so arguments that can be passed to tail(1) can also be passed to plog.

       Note: the plog script can only be used by root or another system administrator in  group  "adm",  due  to
       security  reasons.  Also,  to have all pppd-generated information in one logfile, that plog can show, you
       need the following line in your /etc/syslog.conf file:

       local2.*       -/var/log/ppp.log

/etc/ppp/options
              PPPd system options file.

       /etc/ppp/pap-secrets
              System PAP passwords file.

       /etc/ppp/chap-secrets
              System CHAP passwords file.

       /etc/ppp/peers/
              Directory holding the peer options files. The default file is called provider.

       /etc/chatscripts/provider
              The chat script invoked from the default /etc/ppp/peers/provider.

       /var/log/ppp.log
              The default PPP log file.

       pon, poff, plog - starts up, shuts down or lists the log of PPP connections

pppd(8), chat(8), tail(1).

Debian Project                                      July 2000                                             PON(1)

pon [ isp-name [ options ] ]
       poff [ -r ] [ -d ] [ -c ] [ -a ] [ -h ] [ isp-name ]
       plog [ arguments ]