transmission-daemon — a bittorrent client

       Charles Kerr, Josh Elsasser, Eric Petit, Mitchell Livingston, and Mike Gelfand.

transmission-daemon is a daemon-based Transmission session that can be controlled via RPC  commands  from
       transmission's web interface or transmission-remote(1).

       http_proxy  libcurl uses this environment variable when performing tracker announces.

       TRANSMISSION_HOME
                   Sets the default config-dir.

~/.config/transmission-daemon
               The   config-dir   used   when   neither   [TRANSMISSION_HOME]   nor   [-g]  is  specified.   See
               https://github.com/transmission/transmission/blob/main/docs/Configuration-Files.md    for    more
               information.

       transmission-daemon — a bittorrent client

-a--allowedx.x.x.x,...
               Allow  RPC  access to a comma-delimited whitelist of IP addresses.  Wildcards can be specified in
               an address by using '*'.  Default: "127.0.0.1,::1" Example: "127.0.0.*,192.168.1.*"

       -b--blocklist
               Enable peer blocklists.  Transmission  understands  the  bluetack  blocklist  file  format.   New
               blocklists can be added by copying them into the config-dir's "blocklists" subdirectory.

       -cdirectory
               Directory  to  watch for new .torrent files to be added. As they are added to this directory, the
               daemon will load them into Transmission.

       -C      Do not watch for new .torrent files.

       -B--no-blocklist
               Disable blocklists.

       -d      Dump transmission-daemon's settings to stderr.

       -f--foreground
               Run in the foreground and print errors to stderr.

       -g--config-dirdirectory
               Where to look for configuration files. This can be used to swap between using  the  cli,  daemon,
               gtk,                   and                   qt                   clients.                    See
               https://github.com/transmission/transmission/blob/main/docs/Configuration-Files.md    for    more
               information.

       -er--encryption-required
               Encrypt all peer connections.

       -ep--encryption-preferred
               Prefer encrypted peer connections.

       -et--encryption-tolerated
               Prefer unencrypted peer connections.

       -gsr--global-seedratioratio
               All torrents, unless overridden by a per-torrent setting, should seed until a specific ratio-GSR--no-global-seedratio
               All torrents, unless overridden by a per-torrent setting, should seed regardless of ratio

       -h--help
               Print command-line option descriptions.

       --incomplete-dirdir
               When adding new torrents, store their contents in directory until the torrent is done.

       --no-incomplete-dir
               Don't store incomplete torrents in a different directory.

       -i--bind-address-ipv4
               Listen  for IPv4 BitTorrent connections on a specific address. Only one IPv4 listening address is
               allowed. Default: 0.0.0.0 (All addresses)

       -I--bind-address-ipv6
               Listen for IPv6 BitTorrent connections on a specific address. Only one IPv6 listening address  is
               allowed. Default: :: (All addresses)

       -r--rpc-bind-address
               Listen  for RPC connections on a specific address. This must be an IPv4 or IPv6 address. Only one
               RPC listening address is allowed. Default: 0.0.0.0 (All IPv4 addresses)

       --paused
               Pause all torrents on startup

       -L--peerlimit-globallimit
               Overall peer limit. Useful on embedded systems where the default might  be  unsuitable.  Default:
               240

       -l--peerlimit-torrentlimit
               Peer  limit  per  torrent.  Useful  on  embedded  systems  where the default might be unsuitable.
               Default: 60

       -m--portmap
               Enable portmapping via NAT-PMP or UPnP

       -M--no-portmap
               Disable portmapping

       -o--dht
               Enable distributed hash table (DHT).

       -O--no-dht
               Disable distributed hash table (DHT).

       -p--portport
               Port to open and listen for RPC requests on. Default: 9091

       -P--peerportport
               Port to listen for incoming peers on. Default: 51413

       -t--auth
               Require clients to authenticate themselves.  This  doesn't  do  much  good  unless  username  and
               password are also set.

       -T--no-auth
               Don't require authentication from clients.

       -u--usernameusername
               Used for client authentication.

       -v--passwordpassword
               Used for client authentication.

       -V--version
               Show version number and exit

       --utp   Enable uTP for peer connections.

       --no-utp
               Disable uTP for peer connections.

       -w--download-dir
               Where to store downloaded data.

       -e--logfile
               Where to store transmission's log messages.

       --log-error
               Show error messages

       --log-info
               Show error and info messages

       --log-debug
               Show error, info, and debug messages

       -x--pid-file
               Name of PID file

transmission-create(1),      transmission-daemon(1),      transmission-edit(1),      transmission-gtk(1),
       transmission-qt(1), transmission-remote(1), transmission-show(1)

       https://transmissionbt.com/

                                                  July 21, 2008                           TRANSMISSION-DAEMON(1)

transmission-daemon-htransmission-daemon  [-ax.x.x.x,...]  [-b  |  -B]  [-cdirectory]  [-C]  [-d] [-f] [-gdirectory] [-h]
                           [-pport] [-t | -T] [-uusername] [-vpassword]  [-Pport]  [-m  |  -M]  [-llimit]
                           [-Llimit]  [-er  |  -ep | -et] [-utp | -no-utp] [-V] [-wdownload-dir] [-elogfile]
                           [-xpid-file] [-log-error | -log-info | -log-debug]