With the above in mind, here follows the complete list of fio job parameters.
Unitskb_base=int
Select the interpretation of unit prefixes in input parameters.
1000 Inputs comply with IEC 80000-13 and the International System of Units (SI). Use:
- power-of-2 values with IEC prefixes (e.g., KiB)
- power-of-10 values with SI prefixes (e.g., kB)
1024 Compatibility mode (default). To avoid breaking old scripts:
- power-of-2 values with SI prefixes
- power-of-10 values with IEC prefixes
See bs for more details on input parameters.
Outputs always use correct prefixes. Most outputs include both side-by-side, like:
bw=2383.3kB/s (2327.4KiB/s)
If only one value is reported, then kb_base selects the one to use:
1000 -- SI prefixes
1024 -- IEC prefixes
unit_base=int
Base unit for reporting. Allowed values are:
0 Use auto-detection (default).
8 Byte based.
1 Bit based.
Jobdescriptionname=str
ASCII name of the job. This may be used to override the name printed by fio for this job.
Otherwise the job name is used. On the command line this parameter has the special purpose of also
signaling the start of a new job.
description=str
Text description of the job. Doesn't do anything except dump this text description when this job
is run. It's not parsed.
loops=int
Run the specified number of iterations of this job. Used to repeat the same workload a given
number of times. Defaults to 1.
numjobs=int
Create the specified number of clones of this job. Each clone of job is spawned as an independent
thread or process. May be used to setup a larger number of threads/processes doing the same thing.
Each thread is reported separately; to see statistics for all clones as a whole, use
group_reporting in conjunction with new_group. See --max-jobs. Default: 1.
Timerelatedparametersruntime=time
Limit runtime. The test will run until it completes the configured I/O workload or until it has
run for this specified amount of time, whichever occurs first. It can be quite hard to determine
for how long a specified job will run, so this parameter is handy to cap the total runtime to a
given time. When the unit is omitted, the value is interpreted in seconds.
time_based
If set, fio will run for the duration of the runtime specified even if the file(s) are completely
read or written. It will simply loop over the same workload as many times as the runtime allows.
startdelay=irange(int)
Delay the start of job for the specified amount of time. Can be a single value or a range. When
given as a range, each thread will choose a value randomly from within the range. Value is in
seconds if a unit is omitted.
ramp_time=time
If set, fio will run the specified workload for this amount of time before logging any performance
numbers. Useful for letting performance settle before logging results, thus minimizing the runtime
required for stable results. Note that the ramp_time is considered lead in time for a job, thus it
will increase the total runtime if a special timeout or runtime is specified. When the unit is
omitted, the value is given in seconds.
clocksource=str
Use the given clocksource as the base of timing. The supported options are:
gettimeofdaygettimeofday(2)
clock_gettimeclock_gettime(2)
cpu Internal CPU clock source
cpu is the preferred clocksource if it is reliable, as it is very fast (and fio is heavy on time
calls). Fio will automatically use this clocksource if it's supported and considered reliable on
the system it is running on, unless another clocksource is specifically set. For x86/x86-64 CPUs,
this means supporting TSC Invariant.
gtod_reduce=bool
Enable all of the gettimeofday(2) reducing options (disable_clat, disable_slat,
disable_bw_measurement) plus reduce precision of the timeout somewhat to really shrink the
gettimeofday(2) call count. With this option enabled, we only do about 0.4% of the gettimeofday(2)
calls we would have done if all time keeping was enabled.
gtod_cpu=int
Sometimes it's cheaper to dedicate a single thread of execution to just getting the current time.
Fio (and databases, for instance) are very intensive on gettimeofday(2) calls. With this option,
you can set one CPU aside for doing nothing but logging current time to a shared memory location.
Then the other threads/processes that run I/O workloads need only copy that segment, instead of
entering the kernel with a gettimeofday(2) call. The CPU set aside for doing these time calls will
be excluded from other uses. Fio will manually clear it from the CPU mask of other jobs.
job_start_clock_id=int
The clock_id passed to the call to clock_gettime used to record job_start in the json output
format. Default is 0, or CLOCK_REALTIME.
Targetfile/devicedirectory=str
Prefix filenames with this directory. Used to place files in a different location than `./'. You
can specify a number of directories by separating the names with a ':' character. These
directories will be assigned equally distributed to job clones created by numjobs as long as they
are using generated filenames. If specific filename(s) are set fio will use the first listed
directory, and thereby matching the filename semantic (which generates a file for each clone if
not specified, but lets all clones use the same file if set).
See the filename option for information on how to escape ':' characters within the directory path
itself.
Note: To control the directory fio will use for internal state files use --aux-path.
filename=str
Fio normally makes up a filename based on the job name, thread number, and file number (see
filename_format). If you want to share files between threads in a job or several jobs with fixed
file paths, specify a filename for each of them to override the default. If the ioengine is file
based, you can specify a number of files by separating the names with a ':' colon. So if you
wanted a job to open `/dev/sda' and `/dev/sdb' as the two working files, you would use
`filename=/dev/sda:/dev/sdb'. This also means that whenever this option is specified, nrfiles is
ignored. The size of regular files specified by this option will be size divided by number of
files unless an explicit size is specified by filesize.
Each colon in the wanted path must be escaped with a '\' character. For instance, if the path is
`/dev/dsk/foo@3,0:c' then you would use `filename=/dev/dsk/foo@3,0\:c' and if the path is
`F:\filename' then you would use `filename=F\:\filename'.
On Windows, disk devices are accessed as `\\.\PhysicalDrive0' for the first device,
`\\.\PhysicalDrive1' for the second etc. Note: Windows and FreeBSD prevent write access to areas
of the disk containing in-use data (e.g. filesystems).
For HTTP and S3 access, specify a valid URL path or S3 key, respectively. A filename for path-
style S3 includes a bucket name (`/bucket/k/e.y') while a virtual-hosted-style S3 filename
(`/k/e.y') does not because its bucket name is specified in http_host.
The filename `-' is a reserved name, meaning *stdin* or *stdout*. Which of the two depends on the
read/write direction set.
filename_format=str
If sharing multiple files between jobs, it is usually necessary to have fio generate the exact
names that you want. By default, fio will name a file based on the default file format
specification of `jobname.jobnumber.filenumber'. With this option, that can be customized. Fio
will recognize and replace the following keywords in this string:
$jobname
The name of the worker thread or process.
$clientuid
IP of the fio process when using client/server mode.
$jobnum
The incremental number of the worker thread or process.
$filenum
The incremental number of the file for that worker thread or process.
To have dependent jobs share a set of files, this option can be set to have fio generate filenames
that are shared between the two. For instance, if `testfiles.$filenum' is specified, file number 4
for any job will be named `testfiles.4'. The default of `$jobname.$jobnum.$filenum' will be used
if no other format specifier is given.
If you specify a path then the directories will be created up to the main directory for the file.
So for example if you specify `a/b/c/$jobnum` then the directories a/b/c will be created before
the file setup part of the job. If you specify directory then the path will be relative that
directory, otherwise it is treated as the absolute path.
unique_filename=bool
To avoid collisions between networked clients, fio defaults to prefixing any generated filenames
(with a directory specified) with the source of the client connecting. To disable this behavior,
set this option to 0.
opendir=str
Recursively open any files below directory str. This accepts only a single directory and unlike
related options, colons appearing in the path must not be escaped.
lockfile=str
Fio defaults to not locking any files before it does I/O to them. If a file or file descriptor is
shared, fio can serialize I/O to that file to make the end result consistent. This is usual for
emulating real workloads that share files. The lock modes are:
none No locking. The default.
exclusive
Only one thread or process may do I/O at a time, excluding all others.
readwrite
Read-write locking on the file. Many readers may access the file at the same time,
but writes get exclusive access.
nrfiles=int
Number of files to use for this job. Defaults to 1. The size of files will be size divided by this
unless explicit size is specified by filesize. Files are created for each thread separately, and
each file will have a file number within its name by default, as explained in filename section.
openfiles=int
Number of files to keep open at the same time. Defaults to the same as nrfiles, can be set smaller
to limit the number simultaneous opens.
file_service_type=str
Defines how fio decides which file from a job to service next. The following types are defined:
random Choose a file at random.
roundrobin
Round robin over opened files. This is the default.
sequential
Finish one file before moving on to the next. Multiple files can still be open
depending on openfiles.
zipf Use a Zipf distribution to decide what file to access.
pareto Use a Pareto distribution to decide what file to access.
normal Use a Gaussian (normal) distribution to decide what file to access.
gauss Alias for normal.
For random, roundrobin, and sequential, a postfix can be appended to tell fio how many I/Os to
issue before switching to a new file. For example, specifying `file_service_type=random:8' would
cause fio to issue 8 I/Os before selecting a new file at random. For the non-uniform
distributions, a floating point postfix can be given to influence how the distribution is skewed.
See random_distribution for a description of how that would work.
ioscheduler=str
Attempt to switch the device hosting the file to the specified I/O scheduler before running. If
the file is a pipe, a character device file or if device hosting the file could not be determined,
this option is ignored.
create_serialize=bool
If true, serialize the file creation for the jobs. This may be handy to avoid interleaving of data
files, which may greatly depend on the filesystem used and even the number of processors in the
system. Default: true.
create_fsync=boolfsync(2) the data file after creation. This is the default.
create_on_open=bool
If true, don't pre-create files but allow the job's open() to create a file when it's time to do
I/O. Default: false -- pre-create all necessary files when the job starts.
create_only=bool
If true, fio will only run the setup phase of the job. If files need to be laid out or updated on
disk, only that will be done -- the actual job contents are not executed. Default: false.
allow_file_create=bool
If true, fio is permitted to create files as part of its workload. If this option is false, then
fio will error out if the files it needs to use don't already exist. Default: true.
allow_mounted_write=bool
If this isn't set, fio will abort jobs that are destructive (e.g. that write) to what appears to
be a mounted device or partition. This should help catch creating inadvertently destructive tests,
not realizing that the test will destroy data on the mounted file system. Note that some platforms
don't allow writing against a mounted device regardless of this option. Default: false.
pre_read=bool
If this is given, files will be pre-read into memory before starting the given I/O operation. This
will also clear the invalidate flag, since it is pointless to pre-read and then drop the cache.
This will only work for I/O engines that are seek-able, since they allow you to read the same data
multiple times. Thus it will not work on non-seekable I/O engines (e.g. network, splice). Default:
false.
unlink=bool
Unlink (delete) the job files when done. Not the default, as repeated runs of that job would then
waste time recreating the file set again and again. Default: false.
unlink_each_loop=bool
Unlink (delete) job files after each iteration or loop. Default: false.
zonemode=str
Accepted values are:
none The zonerange, zonesizezonecapacity and zoneskip parameters are ignored.
strided
I/O happens in a single zone until zonesize bytes have been transferred. After that
number of bytes has been transferred processing of the next zone starts. The
zonecapacity parameter is ignored.
zbd Zoned block device mode. I/O happens sequentially in each zone, even if random I/O
has been selected. Random I/O happens across all zones instead of being restricted
to a single zone. Trim is handled using a zone reset operation. Trim only considers
non-empty sequential write required and sequential write preferred zones.
zonerange=int
For zonemode=strided, this is the size of a single zone. See also zonesize and zoneskip.
For zonemode=zbd, this parameter is ignored.
zonesize=int
For zonemode=strided, this is the number of bytes to transfer before skipping zoneskip bytes. If
this parameter is smaller than zonerange then only a fraction of each zone with zonerange bytes
will be accessed. If this parameter is larger than zonerange then each zone will be accessed
multiple times before skipping to the next zone.
For zonemode=zbd, this is the size of a single zone. The zonerange parameter is ignored in this
mode. For a job accessing a zoned block device, the specified zonesize must be 0 or equal to the
device zone size. For a regular block device or file, the specified zonesize must be at least
512B.
zonecapacity=int
For zonemode=zbd, this defines the capacity of a single zone, which is the accessible area
starting from the zone start address. This parameter only applies when using zonemode=zbd in
combination with regular block devices. If not specified it defaults to the zone size. If the
target device is a zoned block device, the zone capacity is obtained from the device information
and this option is ignored.
zoneskip=int[z]
For zonemode=strided, the number of bytes to skip after zonesize bytes of data have been
transferred.
For zonemode=zbd, the zonesize aligned number of bytes to skip once a zone is fully written (write
workloads) or all written data in the zone have been read (read workloads). This parameter is
valid only for sequential workloads and ignored for random workloads. For read workloads, see also
read_beyond_wp.
read_beyond_wp=bool
This parameter applies to zonemode=zbd only.
Zoned block devices are block devices that consist of multiple zones. Each zone has a type, e.g.
conventional or sequential. A conventional zone can be written at any offset that is a multiple of
the block size. Sequential zones must be written sequentially. The position at which a write must
occur is called the write pointer. A zoned block device can be either host managed or host aware.
For host managed devices the host must ensure that writes happen sequentially. Fio recognizes host
managed devices and serializes writes to sequential zones for these devices.
If a read occurs in a sequential zone beyond the write pointer then the zoned block device will
complete the read without reading any data from the storage medium. Since such reads lead to
unrealistically high bandwidth and IOPS numbers fio only reads beyond the write pointer if
explicitly told to do so. Default: false.
max_open_zones=int
When a zone of a zoned block device is partially written (i.e. not all sectors of the zone have
been written), the zone is in one of three conditions: 'implicit open', 'explicit open' or
'closed'. Zoned block devices may have a limit called 'max_open_zones' (same name as the
parameter) on the total number of zones that can simultaneously be in the 'implicit open' or
'explicit open' conditions. Zoned block devices may have another limit called 'max_active_zones',
on the total number of zones that can simultaneously be in the three conditions. The
max_open_zones parameter limits the number of zones to which write commands are issued by all fio
jobs, that is, limits the number of zones that will be in the conditions. When the device has the
max_open_zones limit and does not have the max_active_zones limit, the max_open_zones parameter
limits the number of zones in the two open conditions up to the limit. In this case, fio includes
zones in the two open conditions to the write target zones at fio start. When the device has both
the max_open_zones and the max_active_zones limits, the max_open_zones parameter limits the number
of zones in the three conditions up to the limit. In this case, fio includes zones in the three
conditions to the write target zones at fio start.
This parameter is relevant only if the zonemode=zbd is used. The default value is always equal to
the max_open_zones limit of the target zoned block device and a value higher than this limit
cannot be specified by users unless the option ignore_zone_limits is specified. When
ignore_zone_limits is specified or the target device does not have the max_open_zones limit,
max_open_zones can specify 0 to disable any limit on the number of zones that can be
simultaneously written to by all jobs.
job_max_open_zones=int
In the same manner as max_open_zones, limit the number of open zones per fio job, that is, the
number of zones that a single job can simultaneously write to. A value of zero indicates no limit.
Default: zero.
ignore_zone_limits=bool
If this option is used, fio will ignore the maximum number of open zones limit of the zoned block
device in use, thus allowing the option max_open_zones value to be larger than the device reported
limit. Default: false.
zone_reset_threshold=float
A number between zero and one that indicates the ratio of written bytes in the zones with write
pointers in the IO range to the size of the IO range. When current ratio is above this ratio,
zones are reset periodically as zone_reset_frequency specifies. If there are multiple jobs when
using this option, the IO range for all write jobs has to be the same.
zone_reset_frequency=float
A number between zero and one that indicates how often a zone reset should be issued if the zone
reset threshold has been exceeded. A zone reset is submitted after each (1 / zone_reset_frequency)
write requests. This and the previous parameter can be used to simulate garbage collection
activity.
I/Otypedirect=bool
If value is true, use non-buffered I/O. This is usually O_DIRECT. Note that OpenBSD and ZFS on
Solaris don't support direct I/O. On Windows the synchronous ioengines don't support direct I/O.
Default: false.
buffered=bool
If value is true, use buffered I/O. This is the opposite of the direct option. Defaults to true.
readwrite=str, rw=str
Type of I/O pattern. Accepted values are:
read Sequential reads.
write Sequential writes.
trim Sequential trims (Linux block devices and SCSI character devices only).
randread
Random reads.
randwrite
Random writes.
randtrim
Random trims (Linux block devices and SCSI character devices only).
rw,readwrite
Sequential mixed reads and writes.
randrw Random mixed reads and writes.
trimwrite
Sequential trim+write sequences. Blocks will be trimmed first, then the same blocks
will be written to. So if `io_size=64K' is specified, Fio will trim a total of 64K
bytes and also write 64K bytes on the same trimmed blocks. This behaviour will be
consistent with `number_ios' or other Fio options limiting the total bytes or number
of I/O's.
randtrimwrite
Like trimwrite, but uses random offsets rather than sequential writes.
Fio defaults to read if the option is not specified. For the mixed I/O types, the default is to
split them 50/50. For certain types of I/O the result may still be skewed a bit, since the speed
may be different.
It is possible to specify the number of I/Os to do before getting a new offset by appending
`:<nr>' to the end of the string given. For a random read, it would look like `rw=randread:8' for
passing in an offset modifier with a value of 8. If the suffix is used with a sequential I/O
pattern, then the `<nr>' value specified will be added to the generated offset for each I/O
turning sequential I/O into sequential I/O with holes. For instance, using `rw=write:4k' will
skip 4k for every write. Also see the rw_sequencer option.
rw_sequencer=str
If an offset modifier is given by appending a number to the `rw=str' line, then this option
controls how that number modifies the I/O offset being generated. Accepted values are:
sequential
Generate sequential offset.
identical
Generate the same offset.
sequential is only useful for random I/O, where fio would normally generate a new random offset
for every I/O. If you append e.g. 8 to randread, i.e. `rw=randread:8' you would get a new random
offset for every 8 I/Os. The result would be a sequence of 8 sequential offsets with a random
starting point. However this behavior may change if a sequential I/O reaches end of the file. As
sequential I/O is already sequential, setting sequential for that would not result in any
difference. identical behaves in a similar fashion, except it sends the same offset 8 number of
times before generating a new offset.
Example #1:
rw=randread:8
rw_sequencer=sequential
bs=4k
The generated sequence of offsets will look like this: 4k, 8k, 12k, 16k, 20k, 24k, 28k, 32k, 92k,
96k, 100k, 104k, 108k, 112k, 116k, 120k, 48k, 52k ...
Example #2:
rw=randread:8
rw_sequencer=identical
bs=4k
The generated sequence of offsets will look like this: 4k, 4k, 4k, 4k, 4k, 4k, 4k, 4k, 92k, 92k,
92k, 92k, 92k, 92k, 92k, 92k, 48k, 48k, 48k ...
unified_rw_reporting=str
Fio normally reports statistics on a per data direction basis, meaning that reads, writes, and
trims are accounted and reported separately. This option determines whether fio reports the
results normally, summed together, or as both options. Accepted values are:
none Normal statistics reporting.
mixed Statistics are summed per data direction and reported together.
both Statistics are reported normally, followed by the mixed statistics.
0 Backward-compatible alias for none.
1 Backward-compatible alias for mixed.
2 Alias for both.
randrepeat=bool
Seed all random number generators in a predictable way so the pattern is repeatable across runs.
Default: true.
allrandrepeat=bool
Alias for randrepeat. Default: true.
randseed=int
Seed the random number generators based on this seed value, to be able to control what sequence of
output is being generated. If not set, the random sequence depends on the randrepeat setting.
fallocate=str
Whether pre-allocation is performed when laying down files. Accepted values are:
none Do not pre-allocate space.
native Use a platform's native pre-allocation call but fall back to none behavior if it
fails/is not implemented.
posix Pre-allocate via posix_fallocate(3).
keep Pre-allocate via fallocate(2) with FALLOC_FL_KEEP_SIZE set.
truncate
Extend file to final size using ftruncate|(2) instead of allocating.
0 Backward-compatible alias for none.
1 Backward-compatible alias for posix.
May not be available on all supported platforms. keep is only available on Linux. If using ZFS on
Solaris this cannot be set to posix because ZFS doesn't support pre-allocation. Default: native if
any pre-allocation methods except truncate are available, none if not.
Note that using truncate on Windows will interact surprisingly with non-sequential write patterns.
When writing to a file that has been extended by setting the end-of-file information, Windows will
backfill the unwritten portion of the file up to that offset with zeroes before issuing the new
write. This means that a single small write to the end of an extended file will stall until the
entire file has been filled with zeroes.
fadvise_hint=str
Use posix_fadvise(2) or posix_madvise(2) to advise the kernel what I/O patterns are likely to be
issued. Accepted values are:
0 Backwards compatible hint for "no hint".
1 Backwards compatible hint for "advise with fio workload type". This uses FADV_RANDOM
for a random workload, and FADV_SEQUENTIAL for a sequential workload.
sequential
Advise using FADV_SEQUENTIAL.
random Advise using FADV_RANDOM.
noreuse
Advise using FADV_NOREUSE. This may be a no-op on older Linux kernels. Since Linux
6.3, it provides a hint to the LRU algorithm. See the posix_fadvise(2) man page.
write_hint=str
Use fcntl(2) to advise the kernel what life time to expect from a write. Only supported on Linux,
as of version 4.13. Accepted values are:
none No particular life time associated with this file.
short Data written to this file has a short life time.
medium Data written to this file has a medium life time.
long Data written to this file has a long life time.
extreme
Data written to this file has a very long life time.
The values are all relative to each other, and no absolute meaning should be associated with them.
offset=int[%|z]
Start I/O at the provided offset in the file, given as either a fixed size in bytes, zones or a
percentage. If a percentage is given, the generated offset will be aligned to the minimum
blocksize or to the value of offset_align if provided. Data before the given offset will not be
touched. This effectively caps the file size at `real_size - offset'. Can be combined with size to
constrain the start and end range of the I/O workload. A percentage can be specified by a number
between 1 and 100 followed by '%', for example, `offset=20%' to specify 20%. In ZBD mode, value
can be set as number of zones using 'z'.
offset_align=int
If set to non-zero value, the byte offset generated by a percentage offset is aligned upwards to
this value. Defaults to 0 meaning that a percentage offset is aligned to the minimum block size.
offset_increment=int[%|z]
If this is provided, then the real offset becomes `offset + offset_increment * thread_number',
where the thread number is a counter that starts at 0 and is incremented for each sub-job (i.e.
when numjobs option is specified). This option is useful if there are several jobs which are
intended to operate on a file in parallel disjoint segments, with even spacing between the
starting points. Percentages can be used for this option. If a percentage is given, the generated
offset will be aligned to the minimum blocksize or to the value of offset_align if provided.In ZBD
mode, value can be set as number of zones using 'z'.
number_ios=int
Fio will normally perform I/Os until it has exhausted the size of the region set by size, or if it
exhaust the allocated time (or hits an error condition). With this setting, the range/size can be
set independently of the number of I/Os to perform. When fio reaches this number, it will exit
normally and report status. Note that this does not extend the amount of I/O that will be done, it
will only stop fio if this condition is met before other end-of-job criteria.
fsync=int
If writing to a file, issue an fsync(2) (or its equivalent) of the dirty data for every number of
blocks given. For example, if you give 32 as a parameter, fio will sync the file after every 32
writes issued. If fio is using non-buffered I/O, we may not sync the file. The exception is the sg
I/O engine, which synchronizes the disk cache anyway. Defaults to 0, which means fio does not
periodically issue and wait for a sync to complete. Also see end_fsync and fsync_on_close.
fdatasync=int
Like fsync but uses fdatasync(2) to only sync data and not metadata blocks. In Windows,
DragonFlyBSD or OSX there is no fdatasync(2) so this falls back to using fsync(2). Defaults to 0,
which means fio does not periodically issue and wait for a data-only sync to complete.
write_barrier=int
Make every N-th write a barrier write.
sync_file_range=str:int
Use sync_file_range(2) for every int number of write operations. Fio will track range of writes
that have happened since the last sync_file_range(2) call. str can currently be one or more of:
wait_before
SYNC_FILE_RANGE_WAIT_BEFORE
write SYNC_FILE_RANGE_WRITE
wait_after
SYNC_FILE_RANGE_WRITE_AFTER
So if you do `sync_file_range=wait_before,write:8', fio would use `SYNC_FILE_RANGE_WAIT_BEFORE |
SYNC_FILE_RANGE_WRITE' for every 8 writes. Also see the sync_file_range(2) man page. This option
is Linux specific.
overwrite=bool
If true, writes to a file will always overwrite existing data. If the file doesn't already exist,
it will be created before the write phase begins. If the file exists and is large enough for the
specified write phase, nothing will be done. Default: false.
end_fsync=bool
If true, fsync(2) file contents when a write stage has completed. Default: false.
fsync_on_close=bool
If true, fio will fsync(2) a dirty file on close. This differs from end_fsync in that it will
happen on every file close, not just at the end of the job. Default: false.
rwmixread=int
Percentage of a mixed workload that should be reads. Default: 50.
rwmixwrite=int
Percentage of a mixed workload that should be writes. If both rwmixread and rwmixwrite is given
and the values do not add up to 100%, the latter of the two will be used to override the first.
This may interfere with a given rate setting, if fio is asked to limit reads or writes to a
certain rate. If that is the case, then the distribution may be skewed. Default: 50.
random_distribution=str:float[:float][,str:float][,str:float]
By default, fio will use a completely uniform random distribution when asked to perform random
I/O. Sometimes it is useful to skew the distribution in specific ways, ensuring that some parts of
the data is more hot than others. fio includes the following distribution models:
random Uniform random distribution
zipf Zipf distribution
pareto Pareto distribution
normal Normal (Gaussian) distribution
zoned Zoned random distribution zoned_abs Zoned absolute random distribution
When using a zipf or pareto distribution, an input value is also needed to define the access
pattern. For zipf, this is the `Zipf theta'. For pareto, it's the `Pareto power'. Fio includes a
test program, fio-genzipf, that can be used visualize what the given input values will yield in
terms of hit rates. If you wanted to use zipf with a `theta' of 1.2, you would use
`random_distribution=zipf:1.2' as the option. If a non-uniform model is used, fio will disable use
of the random map. For the normal distribution, a normal (Gaussian) deviation is supplied as a
value between 0 and 100.
The second, optional float is allowed for pareto, zipf and normal distributions. It allows one to
set base of distribution in non-default place, giving more control over most probable outcome.
This value is in range [0-1] which maps linearly to range of possible random values. Defaults
are: random for pareto and zipf, and 0.5 for normal. If you wanted to use zipf with a `theta` of
1.2 centered on 1/4 of allowed value range, you would use `random_distribution=zipf:1.2:0.25`.
For a zoned distribution, fio supports specifying percentages of I/O access that should fall
within what range of the file or device. For example, given a criteria of:
60% of accesses should be to the first 10%
30% of accesses should be to the next 20%
8% of accesses should be to the next 30%
2% of accesses should be to the next 40%
we can define that through zoning of the random accesses. For the above example, the user would
do:
random_distribution=zoned:60/10:30/20:8/30:2/40
A zoned_abs distribution works exactly like thezoned, except that it takes absolute sizes. For
example, let's say you wanted to define access according to the following criteria:
60% of accesses should be to the first 20G
30% of accesses should be to the next 100G
10% of accesses should be to the next 500G
we can define an absolute zoning distribution with:
random_distribution=zoned:60/10:30/20:8/30:2/40
For both zoned and zoned_abs, fio supports defining up to 256 separate zones.
Similarly to how bssplit works for setting ranges and percentages of block sizes. Like bssplit,
it's possible to specify separate zones for reads, writes, and trims. If just one set is given,
it'll apply to all of them.
percentage_random=int[,int][,int]
For a random workload, set how big a percentage should be random. This defaults to 100%, in which
case the workload is fully random. It can be set from anywhere from 0 to 100. Setting it to 0
would make the workload fully sequential. Any setting in between will result in a random mix of
sequential and random I/O, at the given percentages. Comma-separated values may be specified for
reads, writes, and trims as described in blocksize.
norandommap
Normally fio will cover every block of the file when doing random I/O. If this option is given,
fio will just get a new random offset without looking at past I/O history. This means that some
blocks may not be read or written, and that some blocks may be read/written more than once. If
this option is used with verify and multiple blocksizes (via bsrange), only intact blocks are
verified, i.e., partially-overwritten blocks are ignored. With an async I/O engine and an I/O
depth > 1, it is possible for the same block to be overwritten, which can cause verification
errors. Either do not use norandommap in this case, or also use the lfsr random generator.
softrandommap=bool
See norandommap. If fio runs with the random block map enabled and it fails to allocate the map,
if this option is set it will continue without a random block map. As coverage will not be as
complete as with random maps, this option is disabled by default.
random_generator=str
Fio supports the following engines for generating I/O offsets for random I/O:
tausworthe
Strong 2^88 cycle random number generator.
lfsr Linear feedback shift register generator.
tausworthe64
Strong 64-bit 2^258 cycle random number generator.
tausworthe is a strong random number generator, but it requires tracking on the side if we want to
ensure that blocks are only read or written once. lfsr guarantees that we never generate the same
offset twice, and it's also less computationally expensive. It's not a true random generator,
however, though for I/O purposes it's typically good enough. lfsr only works with single block
sizes, not with workloads that use multiple block sizes. If used with such a workload, fio may
read or write some blocks multiple times. The default value is tausworthe, unless the required
space exceeds 2^32 blocks. If it does, then tausworthe64 is selected automatically.
Blocksizeblocksize=int[,int][,int], bs=int[,int][,int]
The block size in bytes used for I/O units. Default: 4096. A single value applies to reads,
writes, and trims. Comma-separated values may be specified for reads, writes, and trims. A value
not terminated in a comma applies to subsequent types. Examples:
bs=256k means 256k for reads, writes and trims.
bs=8k,32k means 8k for reads, 32k for writes and trims.
bs=8k,32k, means 8k for reads, 32k for writes, and default for trims.
bs=,8k means default for reads, 8k for writes and trims.
bs=,8k, means default for reads, 8k for writes, and default for trims.
blocksize_range=irange[,irange][,irange], bsrange=irange[,irange][,irange]
A range of block sizes in bytes for I/O units. The issued I/O unit will always be a multiple of
the minimum size, unless blocksize_unaligned is set. Comma-separated ranges may be specified for
reads, writes, and trims as described in blocksize. Example:
bsrange=1k-4k,2k-8k or bsrange=1k:4k,2k:8k
bssplit=str[,str][,str]
Sometimes you want even finer grained control of the block sizes issued, not just an even split
between them. This option allows you to weight various block sizes, so that you are able to define
a specific amount of block sizes issued. The format for this option is:
bssplit=blocksize/percentage:blocksize/percentage
for as many block sizes as needed. So if you want to define a workload that has 50% 64k blocks,
10% 4k blocks, and 40% 32k blocks, you would write:
bssplit=4k/10:64k/50:32k/40
Ordering does not matter. If the percentage is left blank, fio will fill in the remaining values
evenly. So a bssplit option like this one:
bssplit=4k/50:1k/:32k/
would have 50% 4k ios, and 25% 1k and 32k ios. The percentages always add up to 100, if bssplit is
given a range that adds up to more, it will error out.
Comma-separated values may be specified for reads, writes, and trims as described in blocksize.
If you want a workload that has 50% 2k reads and 50% 4k reads, while having 90% 4k writes and 10%
8k writes, you would specify:
bssplit=2k/50:4k/50,4k/90:8k/10
Fio supports defining up to 64 different weights for each data direction.
blocksize_unaligned, bs_unaligned
If set, fio will issue I/O units with any size within blocksize_range, not just multiples of the
minimum size. This typically won't work with direct I/O, as that normally requires sector
alignment.
bs_is_seq_rand=bool
If this option is set, fio will use the normal read,write blocksize settings as sequential,random
blocksize settings instead. Any random read or write will use the WRITE blocksize settings, and
any sequential read or write will use the READ blocksize settings.
blockalign=int[,int][,int], ba=int[,int][,int]
Boundary to which fio will align random I/O units. Default: blocksize. Minimum alignment is
typically 512b for using direct I/O, though it usually depends on the hardware block size. This
option is mutually exclusive with using a random map for files, so it will turn off that option.
Comma-separated values may be specified for reads, writes, and trims as described in blocksize.
Buffersandmemoryzero_buffers
Initialize buffers with all zeros. Default: fill buffers with random data.
refill_buffers
If this option is given, fio will refill the I/O buffers on every submit. The default is to only
fill it at init time and reuse that data. Only makes sense if zero_buffers isn't specified,
naturally. If data verification is enabled, refill_buffers is also automatically enabled.
scramble_buffers=bool
If refill_buffers is too costly and the target is using data deduplication, then setting this
option will slightly modify the I/O buffer contents to defeat normal de-dupe attempts. This is not
enough to defeat more clever block compression attempts, but it will stop naive dedupe of blocks.
Default: true.
buffer_compress_percentage=int
If this is set, then fio will attempt to provide I/O buffer content (on WRITEs) that compresses to
the specified level. Fio does this by providing a mix of random data followed by fixed pattern
data. The fixed pattern is either zeros, or the pattern specified by buffer_pattern. If the
buffer_pattern option is used, it might skew the compression ratio slightly. Setting
buffer_compress_percentage to a value other than 100 will also enable refill_buffers in order to
reduce the likelihood that adjacent blocks are so similar that they over compress when seen
together. See buffer_compress_chunk for how to set a finer or coarser granularity of the
random/fixed data regions. Defaults to unset i.e., buffer data will not adhere to any compression
level.
buffer_compress_chunk=int
This setting allows fio to manage how big the random/fixed data region is when using
buffer_compress_percentage. When buffer_compress_chunk is set to some non-zero value smaller than
the block size, fio can repeat the random/fixed region throughout the I/O buffer at the specified
interval (which particularly useful when bigger block sizes are used for a job). When set to 0,
fio will use a chunk size that matches the block size resulting in a single random/fixed region
within the I/O buffer. Defaults to 512. When the unit is omitted, the value is interpreted in
bytes.
buffer_pattern=str
If set, fio will fill the I/O buffers with this pattern or with the contents of a file. If not
set, the contents of I/O buffers are defined by the other options related to buffer contents. The
setting can be any pattern of bytes, and can be prefixed with 0x for hex values. It may also be a
string, where the string must then be wrapped with "". Or it may also be a filename, where the
filename must be wrapped with '' in which case the file is opened and read. Note that not all the
file contents will be read if that would cause the buffers to overflow. So, for example:
buffer_pattern='filename'
or:
buffer_pattern="abcd"
or:
buffer_pattern=-12
or:
buffer_pattern=0xdeadface
Also you can combine everything together in any order:
buffer_pattern=0xdeadface"abcd"-12'filename'
dedupe_percentage=int
If set, fio will generate this percentage of identical buffers when writing. These buffers will be
naturally dedupable. The contents of the buffers depend on what other buffer compression settings
have been set. It's possible to have the individual buffers either fully compressible, or not at
all -- this option only controls the distribution of unique buffers. Setting this option will also
enable refill_buffers to prevent every buffer being identical.
dedupe_mode=str
If dedupe_percentage is given, then this option controls how fio generates the dedupe buffers.
repeat
Generate dedupe buffers by repeating previous writes
working_set
Generate dedupe buffers from working set
repeat is the default option for fio. Dedupe buffers are generated by repeating previous unique
write.
working_set is a more realistic workload. With working_set, dedupe_working_set_percentage should
be provided. Given that, fio will use the initial unique write buffers as its working set. Upon
deciding to dedupe, fio will randomly choose a buffer from the working set. Note that by using
working_set the dedupe percentage will converge to the desired over time while repeat maintains
the desired percentage throughout the job.
dedupe_working_set_percentage=int
If dedupe_mode is set to working_set, then this controls the percentage of size of the file or
device used as the buffers fio will choose to generate the dedupe buffers from
Note that size needs to be explicitly provided and only 1 file per job is supported
dedupe_global=bool
This controls whether the deduplication buffers will be shared amongst all jobs that have this
option set. The buffers are spread evenly between participating jobs.
Note that dedupe_mode must be set to working_set for this to work. Can be used in combination
with compression
invalidate=bool
Invalidate the buffer/page cache parts of the files to be used prior to starting I/O if the
platform and file type support it. Defaults to true. This will be ignored if pre_read is
also specified for the same job.
sync=str
Whether, and what type, of synchronous I/O to use for writes. The allowed values are:
none Do not use synchronous IO, the default.
0 Same as none.
sync Use synchronous file IO. For the majority of I/O engines, this means using
O_SYNC.
1 Same as sync.
dsync Use synchronous data IO. For the majority of I/O engines, this means using
O_DSYNC.
iomem=str, mem=str
Fio can use various types of memory as the I/O unit buffer. The allowed values are:
malloc Use memory from malloc(3) as the buffers. Default memory type.
shm Use shared memory as the buffers. Allocated through shmget(2).
shmhuge
Same as shm, but use huge pages as backing.
mmap Use mmap(2) to allocate buffers. May either be anonymous memory, or can be
file backed if a filename is given after the option. The format is
`mem=mmap:/path/to/file'.
mmaphuge
Use a memory mapped huge file as the buffer backing. Append filename after
mmaphuge, ala `mem=mmaphuge:/hugetlbfs/file'.
mmapshared
Same as mmap, but use a MMAP_SHARED mapping.
cudamalloc
Use GPU memory as the buffers for GPUDirect RDMA benchmark. The ioengine
must be rdma.
The area allocated is a function of the maximum allowed bs size for the job, multiplied by
the I/O depth given. Note that for shmhuge and mmaphuge to work, the system must have free
huge pages allocated. This can normally be checked and set by reading/writing
`/proc/sys/vm/nr_hugepages' on a Linux system. Fio assumes a huge page is 2 or 4MiB in size
depending on the platform. So to calculate the number of huge pages you need for a given
job file, add up the I/O depth of all jobs (normally one unless iodepth is used) and
multiply by the maximum bs set. Then divide that number by the huge page size. You can see
the size of the huge pages in `/proc/meminfo'. If no huge pages are allocated by having a
non-zero number in `nr_hugepages', using mmaphuge or shmhuge will fail. Also see
hugepage-size.
mmaphuge also needs to have hugetlbfs mounted and the file location should point there. So
if it's mounted in `/huge', you would use `mem=mmaphuge:/huge/somefile'.
iomem_align=int, mem_align=int
This indicates the memory alignment of the I/O memory buffers. Note that the given
alignment is applied to the first I/O unit buffer, if using iodepth the alignment of the
following buffers are given by the bs used. In other words, if using a bs that is a
multiple of the page sized in the system, all buffers will be aligned to this value. If
using a bs that is not page aligned, the alignment of subsequent I/O memory buffers is the
sum of the iomem_align and bs used.
hugepage-size=int
Defines the size of a huge page. Must at least be equal to the system setting, see
`/proc/meminfo' and `/sys/kernel/mm/hugepages/'. Defaults to 2 or 4MiB depending on the
platform. Should probably always be a multiple of megabytes, so using `hugepage-size=Xm' is
the preferred way to set this to avoid setting a non-pow-2 bad value.
lockmem=int
Pin the specified amount of memory with mlock(2). Can be used to simulate a smaller amount
of memory. The amount specified is per worker.
I/Osizesize=int[%|z]
The total size of file I/O for each thread of this job. Fio will run until this many bytes has
been transferred, unless runtime is altered by other means such as (1) runtime, (2) io_size, (3)
number_ios, (4) gaps/holes while doing I/O's such as `rw=read:16K', or (5) sequential I/O reaching
end of the file which is possible when percentage_random is less than 100. Fio will divide this
size between the available files determined by options such as nrfiles, filename, unless filesize
is specified by the job. If the result of division happens to be 0, the size is set to the
physical size of the given files or devices if they exist. If this option is not specified, fio
will use the full size of the given files or devices. If the files do not exist, size must be
given. It is also possible to give size as a percentage between 1 and 100. If `size=20%' is given,
fio will use 20% of the full size of the given files or devices. In ZBD mode, size can be given in
units of number of zones using 'z'. Can be combined with offset to constrain the start and end
range that I/O will be done within.
io_size=int[%|z], io_limit=int[%|z]
Normally fio operates within the region set by size, which means that the size option sets both
the region and size of I/O to be performed. Sometimes that is not what you want. With this option,
it is possible to define just the amount of I/O that fio should do. For instance, if size is set
to 20GiB and io_size is set to 5GiB, fio will perform I/O within the first 20GiB but exit when
5GiB have been done. The opposite is also possible -- if size is set to 20GiB, and io_size is set
to 40GiB, then fio will do 40GiB of I/O within the 0..20GiB region. Value can be set as
percentage: io_size=N%. In this case io_size multiplies size= value. In ZBD mode, value can also
be set as number of zones using 'z'.
filesize=irange(int)
Individual file sizes. May be a range, in which case fio will select sizes for files at random
within the given range. If not given, each created file is the same size. This option overrides
size in terms of file size, i.e. size becomes merely the default for io_size (and has no effect it
all if io_size is set explicitly).
file_append=bool
Perform I/O after the end of the file. Normally fio will operate within the size of a file. If
this option is set, then fio will append to the file instead. This has identical behavior to
setting offset to the size of a file. This option is ignored on non-regular files.
fill_device=bool, fill_fs=bool
Sets size to something really large and waits for ENOSPC (no space left on device) or EDQUOT (disk
quota exceeded) as the terminating condition. Only makes sense with sequential write. For a read
workload, the mount point will be filled first then I/O started on the result.
I/Oengineioengine=str
fio supports 2 kinds of performance measurement: I/O and file/directory operation.
I/O engines define how the job issues I/O to the file. The following types are defined:
sync Basic read(2) or write(2) I/O. lseek(2) is used to position the I/O location. See fsync
and fdatasync for syncing write I/Os.
psync Basic pread(2) or pwrite(2) I/O. Default on all supported operating systems except for
Windows.
vsync Basic readv(2) or writev(2) I/O. Will emulate queuing by coalescing adjacent I/Os into a
single submission.
pvsync Basic preadv(2) or pwritev(2) I/O.
pvsync2
Basic preadv2(2) or pwritev2(2) I/O.
io_uring
Fast Linux native asynchronous I/O. Supports async IO for both direct and buffered IO.
This engine defines engine specific options.
io_uring_cmd
Fast Linux native asynchronous I/O for passthrough commands. This engine defines engine
specific options.
libaio Linux native asynchronous I/O. Note that Linux may only support queued behavior with non-
buffered I/O (set `direct=1' or `buffered=0'). This engine defines engine specific
options.
posixaio
POSIX asynchronous I/O using aio_read(3) and aio_write(3).
solarisaio
Solaris native asynchronous I/O.
windowsaio
Windows native asynchronous I/O. Default on Windows.
mmap File is memory mapped with mmap(2) and data copied to/from using memcpy(3).
splicesplice(2) is used to transfer the data and vmsplice(2) to transfer data from user space to
the kernel.
sg SCSI generic sg v3 I/O. May either be synchronous using the SG_IO ioctl, or if the target
is an sg character device we use read(2) and write(2) for asynchronous I/O. Requires
filename option to specify either block or character devices. This engine supports trim
operations. The sg engine includes engine specific options.
libzbc Read, write, trim and ZBC/ZAC operations to a zoned block device using libzbc library. The
target can be either an SG character device or a block device file.
null Doesn't transfer any data, just pretends to. This is mainly used to exercise fio itself and
for debugging/testing purposes.
net Transfer over the network to given `host:port'. Depending on the protocol used, the
hostname, port, listen and filename options are used to specify what sort of connection to
make, while the protocol option determines which protocol will be used. This engine defines
engine specific options.
netsplice
Like net, but uses splice(2) and vmsplice(2) to map data and send/receive. This engine
defines engine specific options.
cpuio Doesn't transfer any data, but burns CPU cycles according to the cpuload, cpuchunks and
cpumode options. A job never finishes unless there is at least one non-cpuio job.
cpuload=85 will cause that job to do nothing but burn 85% of the CPU. In case of SMP
machines, use numjobs=<nr_of_cpu> to get desired CPU usage, as the cpuload only loads a
single CPU at the desired rate.
cpumode=qsort replace the default noop instructions loop by a qsort algorithm to consume
more energy.
rdma The RDMA I/O engine supports both RDMA memory semantics (RDMA_WRITE/RDMA_READ) and channel
semantics (Send/Recv) for the InfiniBand, RoCE and iWARP protocols. This engine defines
engine specific options.
falloc I/O engine that does regular fallocate to simulate data transfer as fio ioengine.
DDIR_READ does fallocate(,mode = FALLOC_FL_KEEP_SIZE,).
DIR_WRITE does fallocate(,mode = 0).
DDIR_TRIM does fallocate(,mode = FALLOC_FL_KEEP_SIZE|FALLOC_FL_PUNCH_HOLE).
ftruncate
I/O engine that sends ftruncate(2) operations in response to write (DDIR_WRITE) events.
Each ftruncate issued sets the file's size to the current block offset. blocksize is
ignored.
e4defrag
I/O engine that does regular EXT4_IOC_MOVE_EXT ioctls to simulate defragment activity in
request to DDIR_WRITE event.
rados I/O engine supporting direct access to Ceph Reliable Autonomic Distributed Object Store
(RADOS) via librados. This ioengine defines engine specific options.
rbd I/O engine supporting direct access to Ceph Rados Block Devices (RBD) via librbd without
the need to use the kernel rbd driver. This ioengine defines engine specific options.
http I/O engine supporting GET/PUT requests over HTTP(S) with libcurl to a WebDAV or S3
endpoint. This ioengine defines engine specific options.
This engine only supports direct IO of iodepth=1; you need to scale this via numjobs.
blocksize defines the size of the objects to be created.
TRIM is translated to object deletion.
gfapi Using GlusterFS libgfapi sync interface to direct access to GlusterFS volumes without
having to go through FUSE. This ioengine defines engine specific options.
gfapi_async
Using GlusterFS libgfapi async interface to direct access to GlusterFS volumes without
having to go through FUSE. This ioengine defines engine specific options.
libhdfs
Read and write through Hadoop (HDFS). The filename option is used to specify host,port of
the hdfs name-node to connect. This engine interprets offsets a little differently. In
HDFS, files once created cannot be modified so random writes are not possible. To imitate
this the libhdfs engine expects a bunch of small files to be created over HDFS and will
randomly pick a file from them based on the offset generated by fio backend (see the
example job file to create such files, use `rw=write' option). Please note, it may be
necessary to set environment variables to work with HDFS/libhdfs properly. Each job uses
its own connection to HDFS.
mtd Read, write and erase an MTD character device (e.g., `/dev/mtd0'). Discards are treated as
erases. Depending on the underlying device type, the I/O may have to go in a certain
pattern, e.g., on NAND, writing sequentially to erase blocks and discarding before
overwriting. The trimwrite mode works well for this constraint.
dev-dax
Read and write using device DAX to a persistent memory device (e.g., /dev/dax0.0) through
the PMDK libpmem library.
external
Prefix to specify loading an external I/O engine object file. Append the engine filename,
e.g. `ioengine=external:/tmp/foo.o' to load ioengine `foo.o' in `/tmp'. The path can be
either absolute or relative. See `engines/skeleton_external.c' in the fio source for
details of writing an external I/O engine.
libpmem
Read and write using mmap I/O to a file on a filesystem mounted with DAX on a persistent
memory device through the PMDK libpmem library.
ime_psync
Synchronous read and write using DDN's Infinite Memory Engine (IME). This engine is very
basic and issues calls to IME whenever an IO is queued.
ime_psyncv
Synchronous read and write using DDN's Infinite Memory Engine (IME). This engine uses
iovecs and will try to stack as much IOs as possible (if the IOs are "contiguous" and the
IO depth is not exceeded) before issuing a call to IME.
ime_aio
Asynchronous read and write using DDN's Infinite Memory Engine (IME). This engine will try
to stack as much IOs as possible by creating requests for IME. FIO will then decide when
to commit these requests.
libiscsi
Read and write iscsi lun with libiscsi.
nbd Synchronous read and write a Network Block Device (NBD).
libcufile
I/O engine supporting libcufile synchronous access to nvidia-fs and a GPUDirect Storage-
supported filesystem. This engine performs I/O without transferring buffers between user-
space and the kernel, unless verify is set or cuda_io is posix. iomem must not be
cudamalloc. This ioengine defines engine specific options.
dfs I/O engine supporting asynchronous read and write operations to the DAOS File System (DFS)
via libdfs.
nfs I/O engine supporting asynchronous read and write operations to NFS filesystems from
userspace via libnfs. This is useful for achieving higher concurrency and thus throughput
than is possible via kernel NFS.
exec Execute 3rd party tools. Could be used to perform monitoring during jobs runtime.
xnvme I/O engine using the xNVMe C API, for NVMe devices. The xnvme engine provides flexibility
to access GNU/Linux Kernel NVMe driver via libaio, IOCTLs, io_uring, the SPDK NVMe driver,
or your own custom NVMe driver. The xnvme engine includes engine specific options. (See
https://xnvme.io/).
libblkio
Use the libblkio library (https://gitlab.com/libblkio/libblkio). The specific driver to use
must be set using libblkio_driver. If mem/iomem is not specified, memory allocation is
delegated to libblkio (and so is guaranteed to work with the selected driver). One libblkio
instance is used per process, so all jobs setting option thread will share a single
instance (with one queue per thread) and must specify compatible options. Note that some
drivers don't allow several instances to access the same device or file simultaneously, but
allow it for threads.
File/directory operation engines define how the job operates file or directory.
The following types are defined:
filecreate
Simply create the files and do no I/O to them. You still need to set filesize so that all
the accounting still occurs, but no actual I/O will be done other than creating the file.
Example job file: filecreate-ioengine.fio.
filestat
Simply do stat() and do no I/O to the file. You need to set filesize and nrfiles, so that
files will be created. This engine is to measure file lookup and meta data access.
Example job file: filestat-ioengine.fio.
filedelete
Simply delete the files by unlink() and do no I/O to them. You need to set filesize and
nrfiles, so that the files will be created. This engine is to measure file delete.
Example job file: filedelete-ioengine.fio.
dircreate
Simply create the directories and do no I/O to them. You still need to set filesize so
that all the accounting still occurs, but no actual I/O will be done other than creating
the directories. Example job file: dircreate-ioengine.fio.
dirstat
Simply do stat() and do no I/O to the directories. You need to set filesize and nrfiles, so
that directories will be created. This engine is to measure directory lookup and meta data
access. Example job file: dirstat-ioengine.fio.
dirdelete
Simply delete the directories by rmdir() and do no I/O to them. You need to set filesize
and nrfiles, so that the directories will be created. This engine is to measure directory
delete.
For file and directory operation engines, there is no I/O throughput, then the statistics
data in report have different meanings. The meaningful output indexes are: iops and clat.
bw is meaningless. Refer to section: "Interpreting the output" for more details.
I/Oenginespecificparameters
In addition, there are some parameters which are only valid when a specific ioengine is in use. These are
used identically to normal parameters, with the caveat that when used on the command line, they must come
after the ioengine that defines them is selected.
(io_uring,libaio)cmdprio_percentage=int[,int]
Set the percentage of I/O that will be issued with the highest priority. Default: 0. A single
value applies to reads and writes. Comma-separated values may be specified for reads and writes.
For this option to be effective, NCQ priority must be supported and enabled, and `direct=1' option
must be used. fio must also be run as the root user. Unlike slat/clat/lat stats, which can be
tracked and reported independently, per priority stats only track and report a single type of
latency. By default, completion latency (clat) will be reported, if lat_percentiles is set, total
latency (lat) will be reported.
(io_uring,libaio)cmdprio_class=int[,int]
Set the I/O priority class to use for I/Os that must be issued with a priority when
cmdprio_percentage or cmdprio_bssplit is set. If not specified when cmdprio_percentage or
cmdprio_bssplit is set, this defaults to the highest priority class. A single value applies to
reads and writes. Comma-separated values may be specified for reads and writes. See man ionice(1).
See also the prioclass option.
(io_uring,libaio)cmdprio_hint=int[,int]
Set the I/O priority hint to use for I/Os that must be issued with a priority when
cmdprio_percentage or cmdprio_bssplit is set. If not specified when cmdprio_percentage or
cmdprio_bssplit is set, this defaults to 0 (no hint). A single value applies to reads and writes.
Comma-separated values may be specified for reads and writes. See also the priohint option.
(io_uring,libaio)cmdprio=int[,int]
Set the I/O priority value to use for I/Os that must be issued with a priority when
cmdprio_percentage or cmdprio_bssplit is set. If not specified when cmdprio_percentage or
cmdprio_bssplit is set, this defaults to 0. Linux limits us to a positive value between 0 and 7,
with 0 being the highest. A single value applies to reads and writes. Comma-separated values may
be specified for reads and writes. See man ionice(1). Refer to an appropriate manpage for other
operating systems since the meaning of priority may differ. See also the prio option.
(io_uring,libaio)cmdprio_bssplit=str[,str]
To get a finer control over I/O priority, this option allows specifying the percentage of IOs that
must have a priority set depending on the block size of the IO. This option is useful only when
used together with the option bssplit, that is, multiple different block sizes are used for reads
and writes.
The first accepted format for this option is the same as the format of the bssplit option:
cmdprio_bssplit=blocksize/percentage:blocksize/percentage
In this case, each entry will use the priority class, priority hint and priority level defined by
the options cmdprio_class, cmdprio and cmdprio_hint respectively.
The second accepted format for this option is:
cmdprio_bssplit=blocksize/percentage/class/level:blocksize/percentage/class/level
In this case, the priority class and priority level is defined inside each entry. In comparison
with the first accepted format, the second accepted format does not restrict all entries to have
the same priority class and priority level.
The third accepted format for this option is:
cmdprio_bssplit=blocksize/percentage/class/level/hint:...
This is an extension of the second accepted format that allows one to also specify a priority
hint.
For all formats, only the read and write data directions are supported, values for trim IOs are
ignored. This option is mutually exclusive with the cmdprio_percentage option.
(io_uring,io_uring_cmd)fixedbufs
If fio is asked to do direct IO, then Linux will map pages for each IO call, and release them when
IO is done. If this option is set, the pages are pre-mapped before IO is started. This eliminates
the need to map and release for each IO. This is more efficient, and reduces the IO latency as
well.
(io_uring,io_uring_cmd)nonvectored=int
With this option, fio will use non-vectored read/write commands, where address must contain the
address directly. Default is -1.
(io_uring,io_uring_cmd)force_async
Normal operation for io_uring is to try and issue an sqe as non-blocking first, and if that fails,
execute it in an async manner. With this option set to N, then every N request fio will ask sqe to
be issued in an async manner. Default is 0.
(io_uring,io_uring_cmd,xnvme)hipri
If this option is set, fio will attempt to use polled IO completions. Normal IO completions
generate interrupts to signal the completion of IO, polled completions do not. Hence they are
require active reaping by the application. The benefits are more efficient IO for high IOPS
scenarios, and lower latencies for low queue depth IO.
(io_uring,io_uring_cmd)registerfiles
With this option, fio registers the set of files being used with the kernel. This avoids the
overhead of managing file counts in the kernel, making the submission and completion part more
lightweight. Required for the below sqthread_poll option.
(io_uring,io_uring_cmd,xnvme)sqthread_poll
Normally fio will submit IO by issuing a system call to notify the kernel of available items in
the SQ ring. If this option is set, the act of submitting IO will be done by a polling thread in
the kernel. This frees up cycles for fio, at the cost of using more CPU in the system. As
submission is just the time it takes to fill in the sqe entries and any syscall required to wake
up the idle kernel thread, fio will not report submission latencies.
(io_uring,io_uring_cmd)sqthread_poll_cpu=int
When `sqthread_poll` is set, this option provides a way to define which CPU should be used for the
polling thread.
(io_uring_cmd)cmd_type=str
Specifies the type of uring passthrough command to be used. Supported value is nvme. Default is
nvme.
(libaio)userspace_reap
Normally, with the libaio engine in use, fio will use the io_getevents(3) system call to reap
newly returned events. With this flag turned on, the AIO ring will be read directly from user-
space to reap events. The reaping mode is only enabled when polling for a minimum of 0 events
(e.g. when `iodepth_batch_complete=0').
(pvsync2)hipri
Set RWF_HIPRI on I/O, indicating to the kernel that it's of higher priority than normal.
(pvsync2)hipri_percentage
When hipri is set this determines the probability of a pvsync2 I/O being high priority. The
default is 100%.
(pvsync2,libaio,io_uring,io_uring_cmd)nowait=bool
By default if a request cannot be executed immediately (e.g. resource starvation, waiting on
locks) it is queued and the initiating process will be blocked until the required resource becomes
free. This option sets the RWF_NOWAIT flag (supported from the 4.14 Linux kernel) and the call
will return instantly with EAGAIN or a partial result rather than waiting.
It is useful to also use ignore_error=EAGAIN when using this option. Note: glibc 2.27, 2.28 have
a bug in syscall wrappers preadv2, pwritev2. They return EOPNOTSUP instead of EAGAIN.
For cached I/O, using this option usually means a request operates only with cached data.
Currently the RWF_NOWAIT flag does not supported for cached write. For direct I/O, requests will
only succeed if cache invalidation isn't required, file blocks are fully allocated and the disk
request could be issued immediately.
(pvsync2,libaio,io_uring)atomic=bool
This option means that writes are issued with torn-write protection, meaning that for a power fail
or kernel crash, all or none of the data from the write will be stored, but never a mix of old and
new data. Torn-write protection is also known as atomic writes.
This option sets the RWF_ATOMIC flag (supported from the 6.11 Linux kernel) on a per-IO basis.
Writes with RWF_ATOMIC set will be rejected by the kernel when the file does not support torn-
write protection. To learn a file's torn-write limits, issue statx with STATX_WRITE_ATOMIC.
(io_uring_cmd,xnvme)fdp=bool
Enable Flexible Data Placement mode for write commands.
(io_uring_cmd,xnvme)dataplacement=str
Specifies the data placement directive type to use for write commands. The following types are
supported:
none Do not use a data placement directive. This is the default.
fdp Use Flexible Data placement directives for write commands. This is equivalent to
specifying fdp=1.
streams
Use Streams directives for write commands.
(io_uring_cmd,xnvme)plid_select=str,fdp_pli_select=str
Defines how fio decides which placement ID to use next. The following types are defined:
random Choose a placement ID at random (uniform).
roundrobin
Round robin over available placement IDs. This is the default.
scheme Choose a placement ID (index) based on the scheme file defined by the option
dp_scheme.
The available placement ID (indices) are defined by plids or fdp_pli option except for the case of
scheme.
(io_uring_cmd,xnvme)plids=str,fdp_pli=str
Select which Placement ID Indices (FDP) or Placement IDs (streams) this job is allowed to use for
writes. This option accepts a comma-separated list of values or ranges (e.g., 1,2-4,5,6-8).
For FDP by default, the job will cycle through all available Placement IDs, so use this option to
be selective. The values specified here are array indices for the list of placement IDs returned
by the nvme-cli command `nvme fdp status'. If you want fio to use FDP placement identifiers only
at indices 0, 2 and 5, set `plids=0,2,5'.
For streams this should be a list of Stream IDs.
(io_uring_cmd,xnvme)dp_scheme=str
Defines which placement ID (index) to be selected based on offset(LBA) range. The file should
contains one or more scheme entries in the following format:
0, 10737418240, 0
10737418240, 21474836480, 1
21474836480, 32212254720, 2
...
Each line, a scheme entry, contains start offset, end offset, and placement ID (index) separated
by comma(,). If the write offset is within the range of a certain scheme entry(start offset ≤
offset < end offset), the corresponding placement ID (index) will be selected. If the write offset
belongs to multiple scheme entries, the first matched scheme entry will be applied. If the offset
is not within any range of scheme entry, dspec field will be set to 0, default RUH. (Caution: In
case of multiple devices in a job, all devices of the job will be affected by the scheme. If this
option is specified, the option plids or fdp_pli will be ignored.)
(io_uring_cmd,xnvme)md_per_io_size=int
Size in bytes for separate metadata buffer per IO. Default: 0.
(io_uring_cmd,xnvme)pi_act=int
Action to take when nvme namespace is formatted with protection information. If this is set to 1
and namespace is formatted with metadata size equal to protection information size, fio won't use
separate metadata buffer or extended logical block. If this is set to 1 and namespace is formatted
with metadata size greater than protection information size, fio will not generate or verify the
protection information portion of metadata for write or read case respectively. If this is set to
0, fio generates protection information for write case and verifies for read case. Default: 1.
For 16 bit CRC generation fio will use isa-l if available otherwise it will use the default slower
generator. (see: https://github.com/intel/isa-l)
(io_uring_cmd,xnvme)pi_chk=str[,str][,str]
Controls the protection information check. This can take one or more of these values. Default:
none.
GUARD Enables protection information checking of guard field.
REFTAG Enables protection information checking of logical block reference tag field.
APPTAG Enables protection information checking of application tag field.
(io_uring_cmd,xnvme)apptag=int
Specifies logical block application tag value, if namespace is formatted to use end to end
protection information. Default: 0x1234.
(io_uring_cmd,xnvme)apptag_mask=int
Specifies logical block application tag mask value, if namespace is formatted to use end to end
protection information. Default: 0xffff.
(io_uring_cmd)num_range=int
For trim command this will be the number of ranges to trim per I/O request. The number of logical
blocks per range is determined by the bs option which should be a multiple of logical block size.
This cannot be used with read or write. Note that setting this option > 1, log_offset will not be
able to log all the offsets. Default: 1.
(cpuio)cpuload=int
Attempt to use the specified percentage of CPU cycles. This is a mandatory option when using cpuio
I/O engine.
(cpuio)cpuchunks=int
Split the load into cycles of the given time. In microseconds.
(cpuio)cpumode=str
Specify how to stress the CPU. It can take these two values:
noop This is the default and directs the CPU to execute noop instructions.
qsort Replace the default noop instructions with a qsort algorithm to consume more energy.
(cpuio)exit_on_io_done=bool
Detect when I/O threads are done, then exit.
(libhdfs)namenode=str
The hostname or IP address of a HDFS cluster namenode to contact.
(libhdfs)port=int
The listening port of the HFDS cluster namenode.
(netsplice,net)port=int
The TCP or UDP port to bind to or connect to. If this is used with numjobs to spawn multiple
instances of the same job type, then this will be the starting port number since fio will use a
range of ports.
(rdma)port=int
The port to use for RDMA-CM communication. This should be the same value on the client and the
server side.
(netsplice,net,rdma)hostname=str
The hostname or IP address to use for TCP, UDP or RDMA-CM based I/O. If the job is a TCP listener
or UDP reader, the hostname is not used and must be omitted unless it is a valid UDP multicast
address.
(netsplice,net)interface=str
The IP address of the network interface used to send or receive UDP multicast.
(netsplice,net)ttl=int
Time-to-live value for outgoing UDP multicast packets. Default: 1.
(netsplice,net)nodelay=bool
Set TCP_NODELAY on TCP connections.
(netsplice,net)protocol=str, proto=str
The network protocol to use. Accepted values are:
tcp Transmission control protocol.
tcpv6 Transmission control protocol V6.
udp User datagram protocol.
udpv6 User datagram protocol V6.
unix UNIX domain socket.
vsock VSOCK protocol.
When the protocol is TCP, UDP or VSOCK, the port must also be given, as well as the hostname if
the job is a TCP or VSOCK listener or UDP reader. For unix sockets, the normal filename option
should be used and the port is invalid. When the protocol is VSOCK, the hostname is the CID of
the remote VM.
(netsplice,net)listen
For TCP network connections, tell fio to listen for incoming connections rather than initiating an
outgoing connection. The hostname must be omitted if this option is used.
(netsplice,net)pingpong
Normally a network writer will just continue writing data, and a network reader will just consume
packages. If `pingpong=1' is set, a writer will send its normal payload to the reader, then wait
for the reader to send the same payload back. This allows fio to measure network latencies. The
submission and completion latencies then measure local time spent sending or receiving, and the
completion latency measures how long it took for the other end to receive and send back. For UDP
multicast traffic `pingpong=1' should only be set for a single reader when multiple readers are
listening to the same address.
(netsplice,net)window_size=int
Set the desired socket buffer size for the connection.
(netsplice,net)mss=int
Set the TCP maximum segment size (TCP_MAXSEG).
(e4defrag)donorname=str
File will be used as a block donor (swap extents between files).
(e4defrag)inplace=int
Configure donor file blocks allocation strategy:
0 Default. Preallocate donor's file on init.
1 Allocate space immediately inside defragment event, and free right after event.
(rbd,rados)clustername=str
Specifies the name of the Ceph cluster.
(rbd)rbdname=str
Specifies the name of the RBD.
(rbd,rados)pool=str
Specifies the name of the Ceph pool containing RBD or RADOS data.
(rbd,rados)clientname=str
Specifies the username (without the 'client.' prefix) used to access the Ceph cluster. If the
clustername is specified, the clientname shall be the full *type.id* string. If no type. prefix is
given, fio will add 'client.' by default.
(rados)conf=str
Specifies the configuration path of ceph cluster, so conf file does not have to be
/etc/ceph/ceph.conf.
(rbd,rados)busy_poll=bool
Poll store instead of waiting for completion. Usually this provides better throughput at cost of
higher(up to 100%) CPU utilization.
(rados)touch_objects=bool
During initialization, touch (create if do not exist) all objects (files). Touching all objects
affects ceph caches and likely impacts test results. Enabled by default.
(http)http_host=str
Hostname to connect to. HTTP port 80 is used automatically when the value of the https parameter
is off, and HTTPS port 443 if it is A virtual-hosted-style S3 hostname starts with a bucket name,
while a path-style S3 hostname does not. Default is localhost.
(http)http_user=str
Username for HTTP authentication.
(http)http_pass=str
Password for HTTP authentication.
(http)https=str
Whether to use HTTPS instead of plain HTTP. on enables HTTPS; insecure will enable HTTPS, but
disable SSL peer verification (use with caution!). Default is off.
(http)http_mode=str
Which HTTP access mode to use: webdav, swift, or s3. Default is webdav.
(http)http_s3_region=str
The S3 region/zone to include in the request. Default is us-east-1.
(http)http_s3_key=str
The S3 secret key.
(http)http_s3_keyid=str
The S3 key/access id.
(http)http_s3_sse_customer_key=str
The encryption customer key in SSE server side.
(http)http_s3_sse_customer_algorithm=str
The encryption customer algorithm in SSE server side. Default is AES256(http)http_s3_storage_class=str
Which storage class to access. User-customizable settings. Default is STANDARD(http)http_swift_auth_token=str
The Swift auth token. See the example configuration file on how to retrieve this.
(http)http_verbose=int
Enable verbose requests from libcurl. Useful for debugging. 1 turns on verbose logging from
libcurl, 2 additionally enables HTTP IO tracing. Default is 0(mtd)skip_bad=bool
Skip operations against known bad blocks.
(libhdfs)hdfsdirectory
libhdfs will create chunk in this HDFS directory.
(libhdfs)chunk_size
The size of the chunk to use for each file.
(rdma)verb=str
The RDMA verb to use on this side of the RDMA ioengine connection. Valid values are write, read,
send and recv. These correspond to the equivalent RDMA verbs (e.g. write = rdma_write etc.). Note
that this only needs to be specified on the client side of the connection. See the examples
folder.
(rdma)bindname=str
The name to use to bind the local RDMA-CM connection to a local RDMA device. This could be a
hostname or an IPv4 or IPv6 address. On the server side this will be passed into the
rdma_bind_addr() function and on the client site it will be used in the rdma_resolve_add()
function. This can be useful when multiple paths exist between the client and the server or in
certain loopback configurations.
(filestat)stat_type=str
Specify stat system call type to measure lookup/getattr performance. Default is stat for stat(2).
(sg)hipri
If this option is set, fio will attempt to use polled IO completions. This will have a similar
effect as (io_uring)hipri. Only SCSI READ and WRITE commands will have the SGV4_FLAG_HIPRI set
(not UNMAP (trim) nor VERIFY). Older versions of the Linux sg driver that do not support hipri
will simply ignore this flag and do normal IO. The Linux SCSI Low Level Driver (LLD) that "owns"
the device also needs to support hipri (also known as iopoll and mq_poll). The MegaRAID driver is
an example of a SCSI LLD. Default: clear (0) which does normal (interrupted based) IO.
(sg,io_uring_cmd)readfua=bool
With readfua option set to 1, read operations include the force unit access (fua) flag. Default:
0.
(sg,io_uring_cmd)writefua=bool
With writefua option set to 1, write operations include the force unit access (fua) flag. Default:
0.
(io_uring_cmd)write_mode=str
Specifies the type of write operation. Defaults to 'write'.
write Use Write commands for write operations
uncor Use Write Uncorrectable commands for write operations
zeroes Use Write Zeroes commands for write operations
verify Use Verify commands for write operations
(io_uring_cmd)verify_mode=str
Specifies the type of command to be used in the verification phase. Defaults to 'read'.
read Use Read commands for data verification
compare
Use Compare commands for data verification
(sg)sg_write_mode=str
Specify the type of write commands to issue. This option can take multiple values:
write(default)
Write opcodes are issued as usual
write_and_verify
Issue WRITE AND VERIFY commands. The BYTCHK bit is set to 00b. This directs the
device to carry out a medium verification with no data comparison for the data that
was written. The writefua option is ignored with this selection.
verify This option is deprecated. Use write_and_verify instead.
write_same
Issue WRITE SAME commands. This transfers a single block to the device and writes
this same block of data to a contiguous sequence of LBAs beginning at the specified
offset. fio's block size parameter specifies the amount of data written with each
command. However, the amount of data actually transferred to the device is equal to
the device's block (sector) size. For a device with 512 byte sectors, blocksize=8k
will write 16 sectors with each command. fio will still generate 8k of data for each
command butonly the first 512 bytes will be used and transferred to the device. The
writefua option is ignored with this selection.
same This option is deprecated. Use write_same instead.
write_same_ndob
Issue WRITE SAME(16) commands as above but with the No Data Output Buffer (NDOB) bit
set. No data will be transferred to the device with this bit set. Data written will
be a pre-determined pattern such as all zeroes.
write_stream
Issue WRITE STREAM(16) commands. Use the stream_id option to specify the stream
identifier.
verify_bytchk_00
Issue VERIFY commands with BYTCHK set to 00. This directs the device to carry out a
medium verification with no data comparison.
verify_bytchk_01
Issue VERIFY commands with BYTCHK set to 01. This directs the device to compare the
data on the device with the data transferred to the device.
verify_bytchk_11
Issue VERIFY commands with BYTCHK set to 11. This transfers a single block to the
device and compares the contents of this block with the data on the device beginning
at the specified offset. fio's block size parameter specifies the total amount of
data compared with this command. However, only one block (sector) worth of data is
transferred to the device. This is similar to the WRITE SAME command except that
data is compared instead of written.
(sg)stream_id=int
Set the stream identifier for WRITE STREAM commands. If this is set to 0 (which is not a valid
stream identifier) fio will open a stream and then close it when done. Default is 0.
(nbd)uri=str
Specify the NBD URI of the server to test. The string is a standard NBD URI (see
https://github.com/NetworkBlockDevice/nbd/tree/master/doc). Example URIs:
nbd://localhost:10809nbd+unix:///?socket=/tmp/socketnbds://tlshost/exportname(libcufile)gpu_dev_ids=str
Specify the GPU IDs to use with CUDA. This is a colon-separated list of int. GPUs are assigned to
workers roundrobin. Default is 0.
(libcufile)cuda_io=str
Specify the type of I/O to use with CUDA. This option takes the following values:
cufile(default)
Use libcufile and nvidia-fs. This option performs I/O directly between a GPUDirect
Storage filesystem and GPU buffers, avoiding use of a bounce buffer. If verify is
set, cudaMemcpy is used to copy verification data between RAM and GPU(s).
Verification data is copied from RAM to GPU before a write and from GPU to RAM after
a read. direct must be 1.
posix Use POSIX to perform I/O with a RAM buffer, and use cudaMemcpy to transfer data
between RAM and the GPU(s). Data is copied from GPU to RAM before a write and
copied from RAM to GPU after a read. verify does not affect the use of cudaMemcpy.
(dfs)pool
Specify the label or UUID of the DAOS pool to connect to.
(dfs)cont
Specify the label or UUID of the DAOS container to open.
(dfs)chunk_size
Specify a different chunk size (in bytes) for the dfs file. Use DAOS container's chunk size by
default.
(dfs)object_class
Specify a different object class for the dfs file. Use DAOS container's object class by default.
(nfs)nfs_url
URL in libnfs format, eg nfs://<server|ipv4|ipv6>/path[?arg=val[&arg=val]*] Refer to the libnfs
README for more details.
(exec)program=str
Specify the program to execute. Note the program will receive a SIGTERM when the job is reaching
the time limit. A SIGKILL is sent once the job is over. The delay between the two signals is
defined by grace_time option.
(exec)arguments=str
Specify arguments to pass to program. Some special variables can be expanded to pass fio's job
details to the program :
%r replaced by the duration of the job in seconds
%n replaced by the name of the job
(exec)grace_time=int
Defines the time between the SIGTERM and SIGKILL signals. Default is 1 second.
(exec)std_redirect=bool
If set, stdout and stderr streams are redirected to files named from the job name. Default is
true.
(xnvme)xnvme_async=str
Select the xnvme async command interface. This can take these values.
emu This is default and use to emulate asynchronous I/O by using a single thread to
create a queue pair on top of a synchronous I/O interface using the NVMe driver
IOCTL.
thrpool
Emulate an asynchronous I/O interface with a pool of userspace threads on top of a
synchronous I/O interface using the NVMe driver IOCTL. By default four threads are
used.
io_uring
Linux native asynchronous I/O interface which supports both direct and buffered I/O.
libaio Use Linux aio for Asynchronous I/O
posix Use the posix asynchronous I/O interface to perform one or more I/O operations
asynchronously.
vfio Use the user-space VFIO-based backend, implemented using libvfn instead of SPDK.
nil Do not transfer any data; just pretend to. This is mainly used for introspective
performance evaluation.
(xnvme)xnvme_sync=str
Select the xnvme synchronous command interface. This can take these values.
nvme This is default and uses Linux NVMe Driver ioctl() for synchronous I/O.
psync This supports regular as well as vectored pread() and pwrite() commands.
block This is the same as psync except that it also supports zone management commands
using Linux block layer IOCTLs.
(xnvme)xnvme_admin=str
Select the xnvme admin command interface. This can take these values.
nvme This is default and uses Linux NVMe Driver ioctl() for admin commands.
block Use Linux Block Layer ioctl() and sysfs for admin commands.
(xnvme)xnvme_dev_nsid=int
xnvme namespace identifier for userspace NVMe driver SPDK or vfio.
(xnvme)xnvme_dev_subnqn=str
Sets the subsystem NQN for fabrics. This is for xNVMe to utilize a fabrics target with multiple
systems.
(xnvme)xnvme_mem=str
Select the xnvme memory backend. This can take these values.
posix This is the default posix memory backend for linux NVMe driver.
hugepage
Use hugepages, instead of existing posix memory backend. The memory backend uses
hugetlbfs. This require users to allocate hugepages, mount hugetlbfs and set an
environment variable for XNVME_HUGETLB_PATH.
spdk Uses SPDK's memory allocator.
vfio Uses libvfn's memory allocator. This also specifies the use of libvfn backend
instead of SPDK.
(xnvme)xnvme_iovec
If this option is set, xnvme will use vectored read/write commands.
(libblkio)libblkio_driver=str
The libblkio driver to use. Different drivers access devices through different underlying
interfaces. Available drivers depend on the libblkio version in use and are listed at
https://libblkio.gitlab.io/libblkio/blkio.html#drivers(libblkio)libblkio_path=str
Sets the value of the driver-specific "path" property before connecting the libblkio instance,
which identifies the target device or file on which to perform I/O. Its exact semantics are
driver-dependent and not all drivers may support it; see
https://libblkio.gitlab.io/libblkio/blkio.html#drivers(libblkio)libblkio_pre_connect_props=str
A colon-separated list of additional libblkio properties to be set after creating but before
connecting the libblkio instance. Each property must have the format <name>=<value>. Colons can be
escaped as \:. These are set after the engine sets any other properties, so those can be
overridden. Available properties depend on the libblkio version in use and are listed at
https://libblkio.gitlab.io/libblkio/blkio.html#properties(libblkio)libblkio_num_entries=int
Sets the value of the driver-specific "num-entries" property before starting the libblkio
instance. Its exact semantics are driver-dependent and not all drivers may support it; see
https://libblkio.gitlab.io/libblkio/blkio.html#drivers(libblkio)libblkio_queue_size=int
Sets the value of the driver-specific "queue-size" property before starting the libblkio instance.
Its exact semantics are driver-dependent and not all drivers may support it; see
https://libblkio.gitlab.io/libblkio/blkio.html#drivers(libblkio)libblkio_pre_start_props=str
A colon-separated list of additional libblkio properties to be set after connecting but before
starting the libblkio instance. Each property must have the format <name>=<value>. Colons can be
escaped as \:. These are set after the engine sets any other properties, so those can be
overridden. Available properties depend on the libblkio version in use and are listed at
https://libblkio.gitlab.io/libblkio/blkio.html#properties(libblkio)hipri
Use poll queues. This is incompatible with libblkio_wait_mode=eventfd and
libblkio_force_enable_completion_eventfd.
(libblkio)libblkio_vectored
Submit vectored read and write requests.
(libblkio)libblkio_write_zeroes_on_trim
Submit trims as "write zeroes" requests instead of discard requests.
(libblkio)libblkio_wait_mode=str
How to wait for completions:
block (default)
Use a blocking call to blkioq_do_io().
eventfd
Use a blocking call to read() on the completion eventfd.
loop Use a busy loop with a non-blocking call to blkioq_do_io().
(libblkio)libblkio_force_enable_completion_eventfd
Enable the queue's completion eventfd even when unused. This may impact performance. The default
is to enable it only if libblkio_wait_mode=eventfd.
(windowsaio)no_completion_thread
Avoid using a separate thread for completion polling.
I/Odepthiodepth=int
Number of I/O units to keep in flight against the file. Note that increasing iodepth beyond 1 will
not affect synchronous ioengines (except for small degrees when verify_async is in use). Even
async engines may impose OS restrictions causing the desired depth not to be achieved. This may
happen on Linux when using libaio and not setting `direct=1', since buffered I/O is not async on
that OS. Keep an eye on the I/O depth distribution in the fio output to verify that the achieved
depth is as expected. Default: 1.
iodepth_batch_submit=int, iodepth_batch=int
This defines how many pieces of I/O to submit at once. It defaults to 1 which means that we submit
each I/O as soon as it is available, but can be raised to submit bigger batches of I/O at the
time. If it is set to 0 the iodepth value will be used.
iodepth_batch_complete_min=int, iodepth_batch_complete=int
This defines how many pieces of I/O to retrieve at once. It defaults to 1 which means that we'll
ask for a minimum of 1 I/O in the retrieval process from the kernel. The I/O retrieval will go on
until we hit the limit set by iodepth_low. If this variable is set to 0, then fio will always
check for completed events before queuing more I/O. This helps reduce I/O latency, at the cost of
more retrieval system calls.
iodepth_batch_complete_max=int
This defines maximum pieces of I/O to retrieve at once. This variable should be used along with
iodepth_batch_complete_min=int variable, specifying the range of min and max amount of I/O which
should be retrieved. By default it is equal to iodepth_batch_complete_min value. Example #1:
iodepth_batch_complete_min=1
iodepth_batch_complete_max=<iodepth>
which means that we will retrieve at least 1 I/O and up to the whole submitted queue depth. If
none of I/O has been completed yet, we will wait. Example #2:
iodepth_batch_complete_min=0
iodepth_batch_complete_max=<iodepth>
which means that we can retrieve up to the whole submitted queue depth, but if none of I/O has
been completed yet, we will NOT wait and immediately exit the system call. In this example we
simply do polling.
iodepth_low=int
The low water mark indicating when to start filling the queue again. Defaults to the same as
iodepth, meaning that fio will attempt to keep the queue full at all times. If iodepth is set to
e.g. 16 and iodepth_low is set to 4, then after fio has filled the queue of 16 requests, it will
let the depth drain down to 4 before starting to fill it again.
serialize_overlap=bool
Serialize in-flight I/Os that might otherwise cause or suffer from data races. When two or more
I/Os are submitted simultaneously, there is no guarantee that the I/Os will be processed or
completed in the submitted order. Further, if two or more of those I/Os are writes, any
overlapping region between them can become indeterminate/undefined on certain storage. These
issues can cause verification to fail erratically when at least one of the racing I/Os is changing
data and the overlapping region has a non-zero size. Setting serialize_overlap tells fio to avoid
provoking this behavior by explicitly serializing in-flight I/Os that have a non-zero overlap.
Note that setting this option can reduce both performance and the iodepth achieved.
This option only applies to I/Os issued for a single job except when it is enabled along with
io_submit_mode=offload. In offload mode, fio will check for overlap among all I/Os submitted by
offload jobs with serialize_overlap enabled.
Default: false.
io_submit_mode=str
This option controls how fio submits the I/O to the I/O engine. The default is `inline', which
means that the fio job threads submit and reap I/O directly. If set to `offload', the job threads
will offload I/O submission to a dedicated pool of I/O threads. This requires some coordination
and thus has a bit of extra overhead, especially for lower queue depth I/O where it can increase
latencies. The benefit is that fio can manage submission rates independently of the device
completion rates. This avoids skewed latency reporting if I/O gets backed up on the device side
(the coordinated omission problem). Note that this option cannot reliably be used with async IO
engines.
I/Oratethinkcycles=int
Stall the job for the specified number of cycles after an I/O has completed before issuing the
next. May be used to simulate processing being done by an application. This is not taken into
account for the time to be waited on for thinktime. Might not have any effect on some platforms,
this can be checked by trying a setting a high enough amount of thinkcycles.
thinktime=time
Stall the job for the specified period of time after an I/O has completed before issuing the next.
May be used to simulate processing being done by an application. When the unit is omitted, the
value is interpreted in microseconds. See thinktime_blocks, thinktime_iotime and thinktime_spin.
thinktime_spin=time
Only valid if thinktime is set - pretend to spend CPU time doing something with the data received,
before falling back to sleeping for the rest of the period specified by thinktime. When the unit
is omitted, the value is interpreted in microseconds.
thinktime_blocks=int
Only valid if thinktime is set - control how many blocks to issue, before waiting thinktime usecs.
If not set, defaults to 1 which will make fio wait thinktime usecs after every block. This
effectively makes any queue depth setting redundant, since no more than 1 I/O will be queued
before we have to complete it and do our thinktime. In other words, this setting effectively caps
the queue depth if the latter is larger.
thinktime_blocks_type=str
Only valid if thinktime is set - control how thinktime_blocks triggers. The default is
`complete', which triggers thinktime when fio completes thinktime_blocks blocks. If this is set to
`issue', then the trigger happens at the issue side.
thinktime_iotime=time
Only valid if thinktime is set - control thinktime interval by time. The thinktime stall is
repeated after IOs are executed for thinktime_iotime. For example, `--thinktime_iotime=9s
--thinktime=1s' repeat 10-second cycle with IOs for 9 seconds and stall for 1 second. When the
unit is omitted, thinktime_iotime is interpreted as a number of seconds. If this option is used
together with thinktime_blocks, the thinktime stall is repeated after thinktime_iotime or after
thinktime_blocks IOs, whichever happens first.
rate=int[,int][,int]
Cap the bandwidth used by this job. The number is in bytes/sec, the normal suffix rules apply.
Comma-separated values may be specified for reads, writes, and trims as described in blocksize.
For example, using `rate=1m,500k' would limit reads to 1MiB/sec and writes to 500KiB/sec. Capping
only reads or writes can be done with `rate=,500k' or `rate=500k,' where the former will only
limit writes (to 500KiB/sec) and the latter will only limit reads.
rate_min=int[,int][,int]
Tell fio to do whatever it can to maintain at least this bandwidth. Failing to meet this
requirement will cause the job to exit. Comma-separated values may be specified for reads, writes,
and trims as described in blocksize.
rate_iops=int[,int][,int]
Cap the bandwidth to this number of IOPS. Basically the same as rate, just specified independently
of bandwidth. If the job is given a block size range instead of a fixed value, the smallest block
size is used as the metric. Comma-separated values may be specified for reads, writes, and trims
as described in blocksize.
rate_iops_min=int[,int][,int]
If fio doesn't meet this rate of I/O, it will cause the job to exit. Comma-separated values may
be specified for reads, writes, and trims as described in blocksize.
rate_process=str
This option controls how fio manages rated I/O submissions. The default is `linear', which submits
I/O in a linear fashion with fixed delays between I/Os that gets adjusted based on I/O completion
rates. If this is set to `poisson', fio will submit I/O based on a more real world random request
flow, known as the Poisson process (https://en.wikipedia.org/wiki/Poisson_point_process). The
lambda will be 10^6 / IOPS for the given workload.
rate_ignore_thinktime=bool
By default, fio will attempt to catch up to the specified rate setting, if any kind of thinktime
setting was used. If this option is set, then fio will ignore the thinktime and continue doing IO
at the specified rate, instead of entering a catch-up mode after thinktime is done.
rate_cycle=int
Average bandwidth for rate_min and rate_iops_min over this number of milliseconds. Defaults to
1000.
I/Olatencylatency_target=time
If set, fio will attempt to find the max performance point that the given workload will run at
while maintaining a latency below this target. When the unit is omitted, the value is interpreted
in microseconds. See latency_window and latency_percentile.
latency_window=time
Used with latency_target to specify the sample window that the job is run at varying queue depths
to test the performance. When the unit is omitted, the value is interpreted in microseconds.
latency_percentile=float
The percentage of I/Os that must fall within the criteria specified by latency_target and
latency_window. If not set, this defaults to 100.0, meaning that all I/Os must be equal or below
to the value set by latency_target.
latency_run=bool
Used with latency_target. If false (default), fio will find the highest queue depth that meets
latency_target and exit. If true, fio will continue running and try to meet latency_target by
adjusting queue depth.
max_latency=time[,time][,time]
If set, fio will exit the job with an ETIMEDOUT error if it exceeds this maximum latency. When the
unit is omitted, the value is interpreted in microseconds. Comma-separated values may be specified
for reads, writes, and trims as described in blocksize.
I/Oreplaywrite_iolog=str
Write the issued I/O patterns to the specified file. See read_iolog. Specify a separate file for
each job, otherwise the iologs will be interspersed and the file may be corrupt. This file will be
opened in append mode.
read_iolog=str
Open an iolog with the specified filename and replay the I/O patterns it contains. This can be
used to store a workload and replay it sometime later. The iolog given may also be a blktrace
binary file, which allows fio to replay a workload captured by blktrace. See blktrace(8) for how
to capture such logging data. For blktrace replay, the file needs to be turned into a blkparse
binary data file first (`blkparse <device> -o /dev/null -d file_for_fio.bin'). You can specify a
number of files by separating the names with a ':' character. See the filename option for
information on how to escape ':' characters within the file names. These files will be
sequentially assigned to job clones created by numjobs. '-' is a reserved name, meaning read from
stdin, notably if filename is set to '-' which means stdin as well, then this flag can't be set to
'-'.
read_iolog_chunked=bool
Determines how iolog is read. If false (default) entire read_iolog will be read at once. If
selected true, input from iolog will be read gradually. Useful when iolog is very large, or it is
generated.
merge_blktrace_file=str
When specified, rather than replaying the logs passed to read_iolog, the logs go through a merge
phase which aggregates them into a single blktrace. The resulting file is then passed on as the
read_iolog parameter. The intention here is to make the order of events consistent. This limits
the influence of the scheduler compared to replaying multiple blktraces via concurrent jobs.
merge_blktrace_scalars=float_list
This is a percentage based option that is index paired with the list of files passed to
read_iolog. When merging is performed, scale the time of each event by the corresponding amount.
For example, `--merge_blktrace_scalars="50:100"' runs the first trace in halftime and the second
trace in realtime. This knob is separately tunable from replay_time_scale which scales the trace
during runtime and will not change the output of the merge unlike this option.
merge_blktrace_iters=float_list
This is a whole number option that is index paired with the list of files passed to read_iolog.
When merging is performed, run each trace for the specified number of iterations. For example,
`--merge_blktrace_iters="2:1"' runs the first trace for two iterations and the second trace for
one iteration.
replay_no_stall=bool
When replaying I/O with read_iolog the default behavior is to attempt to respect the timestamps
within the log and replay them with the appropriate delay between IOPS. By setting this variable
fio will not respect the timestamps and attempt to replay them as fast as possible while still
respecting ordering. The result is the same I/O pattern to a given device, but different timings.
replay_time_scale=int
When replaying I/O with read_iolog, fio will honor the original timing in the trace. With this
option, it's possible to scale the time. It's a percentage option, if set to 50 it means run at
50% the original IO rate in the trace. If set to 200, run at twice the original IO rate. Defaults
to 100.
replay_redirect=str
While replaying I/O patterns using read_iolog the default behavior is to replay the IOPS onto the
major/minor device that each IOP was recorded from. This is sometimes undesirable because on a
different machine those major/minor numbers can map to a different device. Changing hardware on
the same system can also result in a different major/minor mapping. replay_redirect causes all
I/Os to be replayed onto the single specified device regardless of the device it was recorded
from. i.e. `replay_redirect=/dev/sdc' would cause all I/O in the blktrace or iolog to be replayed
onto `/dev/sdc'. This means multiple devices will be replayed onto a single device, if the trace
contains multiple devices. If you want multiple devices to be replayed concurrently to multiple
redirected devices you must blkparse your trace into separate traces and replay them with
independent fio invocations. Unfortunately this also breaks the strict time ordering between
multiple device accesses.
replay_align=int
Force alignment of the byte offsets in a trace to this value. The value must be a power of 2.
replay_scale=int
Scale bye offsets down by this factor when replaying traces. Should most likely use replay_align
as well.
Threads,processesandjobsynchronizationreplay_skip=str
Sometimes it's useful to skip certain IO types in a replay trace. This could be, for instance,
eliminating the writes in the trace. Or not replaying the trims/discards, if you are redirecting
to a device that doesn't support them. This option takes a comma separated list of read, write,
trim, sync.
thread Fio defaults to creating jobs by using fork, however if this option is given, fio will create jobs
by using POSIX Threads' function pthread_create(3) to create threads instead.
wait_for=str
If set, the current job won't be started until all workers of the specified waitee job are done.
wait_for operates on the job name basis, so there are a few limitations. First, the waitee must be
defined prior to the waiter job (meaning no forward references). Second, if a job is being
referenced as a waitee, it must have a unique name (no duplicate waitees).
nice=int
Run the job with the given nice value. See man nice(2). On Windows, values less than -15 set the
process class to "High"; -1 through -15 set "Above Normal"; 1 through 15 "Below Normal"; and above
15 "Idle" priority class.
prio=int
Set the I/O priority value of this job. Linux limits us to a positive value between 0 and 7, with
0 being the highest. See man ionice(1). Refer to an appropriate manpage for other operating
systems since meaning of priority may differ. For per-command priority setting, see the I/O engine
specific `cmdprio_percentage` and `cmdprio` options.
prioclass=int
Set the I/O priority class. See man ionice(1). For per-command priority setting, see the I/O
engine specific `cmdprio_percentage` and `cmdprio_class` options.
priohint=int
Set the I/O priority hint. This is only applicable to platforms that support I/O priority classes
and to devices with features controlled through priority hints, e.g. block devices supporting
command duration limits, or CDL. CDL is a way to indicate the desired maximum latency of I/Os so
that the device can optimize its internal command scheduling according to the latency limits
indicated by the user. For per-I/O priority hint setting, see the I/O engine specific cmdprio_hintoption.cpus_allowed=str
Controls the same options as cpumask, but accepts a textual specification of the permitted CPUs
instead and CPUs are indexed from 0. So to use CPUs 0 and 5 you would specify `cpus_allowed=0,5'.
This option also allows a range of CPUs to be specified -- say you wanted a binding to CPUs 0, 5,
and 8 to 15, you would set `cpus_allowed=0,5,8-15'.
On Windows, when `cpus_allowed' is unset only CPUs from fio's current processor group will be used
and affinity settings are inherited from the system. An fio build configured to target Windows 7
makes options that set CPUs processor group aware and values will set both the processor group and
a CPU from within that group. For example, on a system where processor group 0 has 40 CPUs and
processor group 1 has 32 CPUs, `cpus_allowed' values between 0 and 39 will bind CPUs from
processor group 0 and `cpus_allowed' values between 40 and 71 will bind CPUs from processor group
1. When using `cpus_allowed_policy=shared' all CPUs specified by a single `cpus_allowed' option
must be from the same processor group. For Windows fio builds not built for Windows 7, CPUs will
only be selected from (and be relative to) whatever processor group fio happens to be running in
and CPUs from other processor groups cannot be used.
cpus_allowed_policy=str
Set the policy of how fio distributes the CPUs specified by cpus_allowed or cpumask. Two policies
are supported:
shared All jobs will share the CPU set specified.
split Each job will get a unique CPU from the CPU set.
shared is the default behavior, if the option isn't specified. If split is specified, then fio
will assign one cpu per job. If not enough CPUs are given for the jobs listed, then fio will
roundrobin the CPUs in the set.
cpumask=int
Set the CPU affinity of this job. The parameter given is a bit mask of allowed CPUs the job may
run on. So if you want the allowed CPUs to be 1 and 5, you would pass the decimal value of (1 << 1
| 1 << 5), or 34. See man sched_setaffinity(2). This may not work on all supported operating
systems or kernel versions. This option doesn't work well for a higher CPU count than what you can
store in an integer mask, so it can only control cpus 1-32. For boxes with larger CPU counts, use
cpus_allowed.
numa_cpu_nodes=str
Set this job running on specified NUMA nodes' CPUs. The arguments allow comma delimited list of
cpu numbers, A-B ranges, or `all'. Note, to enable NUMA options support, fio must be built on a
system with libnuma-dev(el) installed.
numa_mem_policy=str
Set this job's memory policy and corresponding NUMA nodes. Format of the arguments:
<mode>[:<nodelist>]
`mode' is one of the following memory policies: `default', `prefer', `bind', `interleave' or
`local'. For `default' and `local' memory policies, no node needs to be specified. For `prefer',
only one node is allowed. For `bind' and `interleave' the `nodelist' may be as follows: a comma
delimited list of numbers, A-B ranges, or `all'.
cgroup=str
Add job to this control group. If it doesn't exist, it will be created. The system must have a
mounted cgroup blkio mount point for this to work. If your system doesn't have it mounted, you can
do so with:
# mount -t cgroup -o blkio none /cgroup
cgroup_weight=int
Set the weight of the cgroup to this value. See the documentation that comes with the kernel,
allowed values are in the range of 100..1000.
cgroup_nodelete=bool
Normally fio will delete the cgroups it has created after the job completion. To override this
behavior and to leave cgroups around after the job completion, set `cgroup_nodelete=1'. This can
be useful if one wants to inspect various cgroup files after job completion. Default: false.
flow_id=int
The ID of the flow. If not specified, it defaults to being a global flow. See flow.
flow=int
Weight in token-based flow control. If this value is used, then fio regulates the activity between
two or more jobs sharing the same flow_id. Fio attempts to keep each job activity proportional to
other jobs' activities in the same flow_id group, with respect to requested weight per job. That
is, if one job has `flow=3', another job has `flow=2' and another with `flow=1`, then there will
be a roughly 3:2:1 ratio in how much one runs vs the others.
flow_sleep=int
The period of time, in microseconds, to wait after the flow counter has exceeded its proportion
before retrying operations.
stonewall, wait_for_previous
Wait for preceding jobs in the job file to exit, before starting this one. Can be used to insert
serialization points in the job file. A stone wall also implies starting a new reporting group,
see group_reporting. Optionally you can use `stonewall=0` to disable or `stonewall=1` to enable
it.
exitall
By default, fio will continue running all other jobs when one job finishes. Sometimes this is not
the desired action. Setting exitall will instead make fio terminate all jobs in the same group, as
soon as one job of that group finishes.
exit_what=str
By default, fio will continue running all other jobs when one job finishes. Sometimes this is not
the desired action. Setting exitall will instead make fio terminate all jobs in the same group.
The option exit_what allows you to control which jobs get terminated when exitall is enabled. The
default value is group. The allowed values are:
all terminates all jobs.
group is the default and does not change the behaviour of exitall.
stonewall
terminates all currently running jobs across all groups and continues execution with
the next stonewalled group.
exec_prerun=str
Before running this job, issue the command specified through system(3). Output is redirected in a
file called `jobname.prerun.txt'.
exec_postrun=str
After the job completes, issue the command specified though system(3). Output is redirected in a
file called `jobname.postrun.txt'.
uid=int
Instead of running as the invoking user, set the user ID to this value before the thread/process
does any work.
gid=int
Set group ID, see uid.
Verificationverify_only
Do not perform specified workload, only verify data still matches previous invocation of this
workload. This option allows one to check data multiple times at a later date without overwriting
it. This option makes sense only for workloads that write data, and does not support workloads
with the time_based option set.
do_verify=bool
Run the verify phase after a write phase. Only valid if verify is set. Default: true.
verify=str
If writing to a file, fio can verify the file contents after each iteration of the job. Each
verification method also implies verification of special header, which is written to the beginning
of each block. This header also includes meta information, like offset of the block, block number,
timestamp when block was written, etc. verify can be combined with verify_pattern option. The
allowed values are:
md5 Use an md5 sum of the data area and store it in the header of each block.
crc64 Use an experimental crc64 sum of the data area and store it in the header of each
block.
crc32c Use a crc32c sum of the data area and store it in the header of each block. This
will automatically use hardware acceleration (e.g. SSE4.2 on an x86 or CRC crypto
extensions on ARM64) but will fall back to software crc32c if none is found.
Generally the fastest checksum fio supports when hardware accelerated.
crc32c-intel
Synonym for crc32c.
crc32 Use a crc32 sum of the data area and store it in the header of each block.
crc16 Use a crc16 sum of the data area and store it in the header of each block.
crc7 Use a crc7 sum of the data area and store it in the header of each block.
xxhash Use xxhash as the checksum function. Generally the fastest software checksum that
fio supports.
sha512 Use sha512 as the checksum function.
sha256 Use sha256 as the checksum function.
sha1 Use optimized sha1 as the checksum function.
sha3-224
Use optimized sha3-224 as the checksum function.
sha3-256
Use optimized sha3-256 as the checksum function.
sha3-384
Use optimized sha3-384 as the checksum function.
sha3-512
Use optimized sha3-512 as the checksum function.
meta This option is deprecated, since now meta information is included in generic
verification header and meta verification happens by default. For detailed
information see the description of the verify setting. This option is kept because
of compatibility's sake with old configurations. Do not use it.
pattern
Verify a strict pattern. Normally fio includes a header with some basic information
and checksumming, but if this option is set, only the specific pattern set with
verify_pattern is verified.
null Only pretend to verify. Useful for testing internals with `ioengine=null', not for
much else.
This option can be used for repeated burn-in tests of a system to make sure that the written data
is also correctly read back. If the data direction given is a read or random read, fio will assume
that it should verify a previously written file. If the data direction includes any form of write,
the verify will be of the newly written data.
To avoid false verification errors, do not use the norandommap option when verifying data with
async I/O engines and I/O depths > 1. Or use the norandommap and the lfsr random generator
together to avoid writing to the same offset with multiple outstanding I/Os.
verify_offset=int
Swap the verification header with data somewhere else in the block before writing. It is swapped
back before verifying.
verify_interval=int
Write the verification header at a finer granularity than the blocksize. It will be written for
chunks the size of verify_interval. blocksize should divide this evenly.
verify_pattern=str
If set, fio will fill the I/O buffers with this pattern. Fio defaults to filling with totally
random bytes, but sometimes it's interesting to fill with a known pattern for I/O verification
purposes. Depending on the width of the pattern, fio will fill 1/2/3/4 bytes of the buffer at the
time (it can be either a decimal or a hex number). The verify_pattern if larger than a 32-bit
quantity has to be a hex number that starts with either "0x" or "0X". Use with verify. Also,
verify_pattern supports %o format, which means that for each block offset will be written and then
verified back, e.g.:
verify_pattern=%o
Or use combination of everything:
verify_pattern=0xff%o"abcd"-12
verify_fatal=bool
Normally fio will keep checking the entire contents before quitting on a block verification
failure. If this option is set, fio will exit the job on the first observed failure. Default:
false.
verify_dump=bool
If set, dump the contents of both the original data block and the data block we read off disk to
files. This allows later analysis to inspect just what kind of data corruption occurred. Off by
default.
verify_async=int
Fio will normally verify I/O inline from the submitting thread. This option takes an integer
describing how many async offload threads to create for I/O verification instead, causing fio to
offload the duty of verifying I/O contents to one or more separate threads. If using this offload
option, even sync I/O engines can benefit from using an iodepth setting higher than 1, as it
allows them to have I/O in flight while verifies are running. Defaults to 0 async threads, i.e.
verification is not asynchronous.
verify_async_cpus=str
Tell fio to set the given CPU affinity on the async I/O verification threads. See cpus_allowed for
the format used.
verify_backlog=int
Fio will normally verify the written contents of a job that utilizes verify once that job has
completed. In other words, everything is written then everything is read back and verified. You
may want to verify continually instead for a variety of reasons. Fio stores the meta data
associated with an I/O block in memory, so for large verify workloads, quite a bit of memory would
be used up holding this meta data. If this option is enabled, fio will write only N blocks before
verifying these blocks.
verify_backlog_batch=int
Control how many blocks fio will verify if verify_backlog is set. If not set, will default to the
value of verify_backlog (meaning the entire queue is read back and verified). If
verify_backlog_batch is less than verify_backlog then not all blocks will be verified, if
verify_backlog_batch is larger than verify_backlog, some blocks will be verified more than once.
verify_state_save=bool
When a job exits during the write phase of a verify workload, save its current state. This allows
fio to replay up until that point, if the verify state is loaded for the verify read phase. The
format of the filename is, roughly:
<type>-<jobname>-<jobindex>-verify.state.
<type> is "local" for a local run, "sock" for a client/server socket connection, and "ip"
(192.168.0.1, for instance) for a networked client/server connection. Defaults to true.
verify_state_load=bool
If a verify termination trigger was used, fio stores the current write state of each thread. This
can be used at verification time so that fio knows how far it should verify. Without this
information, fio will run a full verification pass, according to the settings in the job file
used. Default false.
experimental_verify=bool
Enable experimental verification. Standard verify records I/O metadata for later use during the
verification phase. Experimental verify instead resets the file after the write phase and then
replays I/Os for the verification phase.
verify_write_sequence=bool
Verify the header write sequence number. In a scenario with multiple jobs, verification of the
write sequence number may fail. Disabling this option will mean that write sequence number
checking is skipped. Doing that can be useful for testing atomic writes, as it means that checksum
verification can still be attempted. For when atomic is enabled, checksum verification is expected
to succeed (while write sequence checking can still fail).
trim_percentage=int
Number of verify blocks to discard/trim.
trim_verify_zero=bool
Verify that trim/discarded blocks are returned as zeros.
trim_backlog=int
Verify that trim/discarded blocks are returned as zeros.
trim_backlog_batch=int
Trim this number of I/O blocks.
Steadystatesteadystate=str:float, ss=str:float
Define the criterion and limit for assessing steady state performance. The first parameter
designates the criterion whereas the second parameter sets the threshold. When the criterion falls
below the threshold for the specified duration, the job will stop. For example, `iops_slope:0.1%'
will direct fio to terminate the job when the least squares regression slope falls below 0.1% of
the mean IOPS. If group_reporting is enabled this will apply to all jobs in the group. Below is
the list of available steady state assessment criteria. All assessments are carried out using only
data from the rolling collection window. Threshold limits can be expressed as a fixed value or as
a percentage of the mean in the collection window.
When using this feature, most jobs should include the time_based and runtime options or the loops
option so that fio does not stop running after it has covered the full size of the specified
file(s) or device(s).
iops Collect IOPS data. Stop the job if all individual IOPS measurements are
within the specified limit of the mean IOPS (e.g., `iops:2' means that all
individual IOPS values must be within 2 of the mean, whereas `iops:0.2%'
means that all individual IOPS values must be within 0.2% of the mean IOPS to
terminate the job).
iops_slope
Collect IOPS data and calculate the least squares regression slope. Stop the
job if the slope falls below the specified limit.
bw Collect bandwidth data. Stop the job if all individual bandwidth measurements
are within the specified limit of the mean bandwidth.
bw_slope
Collect bandwidth data and calculate the least squares regression slope. Stop
the job if the slope falls below the specified limit.
steadystate_duration=time, ss_dur=time
A rolling window of this duration will be used to judge whether steady state has been
reached. Data will be collected every ss_interval. The default is 0 which disables steady
state detection. When the unit is omitted, the value is interpreted in seconds.
steadystate_ramp_time=time, ss_ramp=time
Allow the job to run for the specified duration before beginning data collection for
checking the steady state job termination criterion. The default is 0. When the unit is
omitted, the value is interpreted in seconds.
steadystate_check_interval=time, ss_interval=time
The values suring the rolling window will be collected with a period of this value. If
ss_interval is 30s and ss_dur is 300s, 10 measurements will be taken. Default is 1s but
that might not converge, especially for slower devices, so set this accordingly. When the
unit is omitted, the value is interpreted in seconds.
Measurementsandreportingper_job_logs=bool
If set to true, fio generates bw/clat/iops logs with per job unique filenames. If set to false,
jobs with identical names will share a log filename. Note that when this option is set to false
log files will be opened in append mode and if log files already exist the previous contents will
not be overwritten. Default: true.
group_reporting
It may sometimes be interesting to display statistics for groups of jobs as a whole instead of for
each individual job. This is especially true if numjobs is used; looking at individual
thread/process output quickly becomes unwieldy. To see the final report per-group instead of per-
job, use group_reporting. Jobs in a file will be part of the same reporting group, unless if
separated by a stonewall, or by using new_group.
NOTE: When group_reporting is used along with json output, there are certain per-job properties
which can be different between jobs but do not have a natural group-level equivalent. Examples
include kb_base, unit_base, sig_figs, thread_number, pid, and job_start. For these properties, the
values for the first job are recorded for the group.
new_group
Start a new reporting group. See: group_reporting. If not given, all jobs in a file will be part
of the same reporting group, unless separated by a stonewall.
stats=bool
By default, fio collects and shows final output results for all jobs that run. If this option is
set to 0, then fio will ignore it in the final stat output.
write_bw_log=str
If given, write a bandwidth log for this job. Can be used to store data of the bandwidth of the
jobs in their lifetime.
If no str argument is given, the default filename of `jobname_type.x.log' is used. Even when the
argument is given, fio will still append the type of log. So if one specifies:
write_bw_log=foo
The actual log name will be `foo_bw.x.log' where `x' is the index of the job (1..N, where N is the
number of jobs). If per_job_logs is false, then the filename will not include the `.x` job index.
The included fio_generate_plots script uses gnuplot to turn these text files into nice graphs. See
the LOGFILEFORMATS section for how data is structured within the file.
write_lat_log=str
Same as write_bw_log, except this option creates I/O submission (e.g., `name_slat.x.log'),
completion (e.g., `name_clat.x.log'), and total (e.g., `name_lat.x.log') latency files instead.
See write_bw_log for details about the filename format and the LOGFILEFORMATS section for how
data is structured within the files.
write_hist_log=str
Same as write_bw_log but writes an I/O completion latency histogram file (e.g., `name_hist.x.log')
instead. Note that this file will be empty unless log_hist_msec has also been set. See
write_bw_log for details about the filename format and the LOGFILEFORMATS section for how data
is structured within the file.
write_iops_log=str
Same as write_bw_log, but writes an IOPS file (e.g. `name_iops.x.log`) instead. Because fio
defaults to individual I/O logging, the value entry in the IOPS log will be 1 unless windowed
logging (see log_avg_msec) has been enabled. See write_bw_log for details about the filename
format and LOGFILEFORMATS for how data is structured within the file.
log_entries=int
By default, fio will log an entry in the iops, latency, or bw log for every I/O that completes.
The initial number of I/O log entries is 1024. When the log entries are all used, new log entries
are dynamically allocated. This dynamic log entry allocation may negatively impact time-related
statistics such as I/O tail latencies (e.g. 99.9th percentile completion latency). This option
allows specifying a larger initial number of log entries to avoid run-time allocation of new log
entries, resulting in more precise time-related I/O statistics. Also see log_avg_msec as well.
Defaults to 1024.
log_avg_msec=int
By default, fio will log an entry in the iops, latency, or bw log for every I/O that completes.
When writing to the disk log, that can quickly grow to a very large size. Setting this option
directs fio to instead record an average over the specified duration for each log entry, reducing
the resolution of the log. When the job completes, fio will flush any accumulated latency log
data, so the final log interval may not match the value specified by this option and there may
even be duplicate timestamps. See log_window_value as well. Defaults to 0, logging entries for
each I/O. Also see LOGFILEFORMATS section.
log_hist_msec=int
Same as log_avg_msec, but logs entries for completion latency histograms. Computing latency
percentiles from averages of intervals using log_avg_msec is inaccurate. Setting this option makes
fio log histogram entries over the specified period of time, reducing log sizes for high IOPS
devices while retaining percentile accuracy. See log_hist_coarseness and write_hist_log as well.
Defaults to 0, meaning histogram logging is disabled.
log_hist_coarseness=int
Integer ranging from 0 to 6, defining the coarseness of the resolution of the histogram logs
enabled with log_hist_msec. For each increment in coarseness, fio outputs half as many bins.
Defaults to 0, for which histogram logs contain 1216 latency bins. See LOGFILEFORMATS section.
log_window_value=str, log_max_value=str
If log_avg_msec is set, fio by default logs the average over that window. This option determines
whether fio logs the average, maximum or both the values over the window. This only affects the
latency logging, as both average and maximum values for iops or bw log will be same. Accepted
values are:
avg Log average value over the window. The default.
max Log maximum value in the window.
both Log both average and maximum value over the window.
0 Backward-compatible alias for avg.
1 Backward-compatible alias for max.
log_offset=bool
If this is set, the iolog options will include the byte offset for the I/O entry as well as the
other data values. Defaults to 0 meaning that offsets are not present in logs. Also see LOGFILEFORMATS section.
log_prio=bool
If this is set, the `Command priority` field in LOGFILEFORMATS shows the priority value and the
IO priority class of the command. Otherwise, the field shows if the command has the highest RT
priority class or not. Also see LOGFILEFORMATS section.
log_issue_time=bool
If this is set, the iolog options will include the command issue time for the I/O entry as well as
the other data values. Defaults to 0 meaning that command issue times are not present in logs.
Also see LOGFILEFORMATS section. This option shall be set together with write_lat_log and
log_offset.
log_compression=int
If this is set, fio will compress the I/O logs as it goes, to keep the memory footprint lower.
When a log reaches the specified size, that chunk is removed and compressed in the background.
Given that I/O logs are fairly highly compressible, this yields a nice memory savings for longer
runs. The downside is that the compression will consume some background CPU cycles, so it may
impact the run. This, however, is also true if the logging ends up consuming most of the system
memory. So pick your poison. The I/O logs are saved normally at the end of a run, by decompressing
the chunks and storing them in the specified log file. This feature depends on the availability of
zlib.
log_compression_cpus=str
Define the set of CPUs that are allowed to handle online log compression for the I/O jobs. This
can provide better isolation between performance sensitive jobs, and background compression work.
See cpus_allowed for the format used.
log_store_compressed=bool
If set, fio will store the log files in a compressed format. They can be decompressed with fio,
using the --inflate-log command line parameter. The files will be stored with a `.fz' suffix.
log_unix_epoch=bool
Backward-compatible alias for log_alternate_epoch.
log_alternate_epoch=bool
If set, fio will log timestamps based on the epoch used by the clock specified in the
log_alternate_epoch_clock_id option, to the log files produced by enabling write_type_log for each
log type, instead of the default zero-based timestamps.
log_alternate_epoch_clock_id=int
Specifies the clock_id to be used by clock_gettime to obtain the alternate epoch if
log_alternate_epoch is true. Otherwise has no effect. Default value is 0, or CLOCK_REALTIME.
block_error_percentiles=bool
If set, record errors in trim block-sized units from writes and trims and output a histogram of
how many trims it took to get to errors, and what kind of error was encountered.
bwavgtime=int
Average the calculated bandwidth over the given time. Value is specified in milliseconds. If the
job also does bandwidth logging through write_bw_log, then the minimum of this option and
log_avg_msec will be used. Default: 500ms.
iopsavgtime=int
Average the calculated IOPS over the given time. Value is specified in milliseconds. If the job
also does IOPS logging through write_iops_log, then the minimum of this option and log_avg_msec
will be used. Default: 500ms.
disk_util=bool
Generate disk utilization statistics, if the platform supports it. Default: true.
disable_lat=bool
Disable measurements of total latency numbers. Useful only for cutting back the number of calls to
gettimeofday(2), as that does impact performance at really high IOPS rates. Note that to really
get rid of a large amount of these calls, this option must be used with disable_slat and
disable_bw_measurement as well.
disable_clat=bool
Disable measurements of completion latency numbers. See disable_lat.
disable_slat=bool
Disable measurements of submission latency numbers. See disable_lat.
disable_bw_measurement=bool, disable_bw=bool
Disable measurements of throughput/bandwidth numbers. See disable_lat.
slat_percentiles=bool
Report submission latency percentiles. Submission latency is not recorded for synchronous
ioengines.
clat_percentiles=bool
Report completion latency percentiles.
lat_percentiles=bool
Report total latency percentiles. Total latency is the sum of submission latency and completion
latency.
percentile_list=float_list
Overwrite the default list of percentiles for latencies and the block error histogram. Each number
is a floating point number in the range (0,100], and the maximum length of the list is 20. Use ':'
to separate the numbers. For example, `--percentile_list=99.5:99.9' will cause fio to report the
latency durations below which 99.5% and 99.9% of the observed latencies fell, respectively.
significant_figures=int
If using --output-format of `normal', set the significant figures to this value. Higher values
will yield more precise IOPS and throughput units, while lower values will round. Requires a
minimum value of 1 and a maximum value of 10. Defaults to 4.
Errorhandlingexitall_on_error
When one job finishes in error, terminate the rest. The default is to wait for each job to finish.
continue_on_error=str
Normally fio will exit the job on the first observed failure. If this option is set, fio will
continue the job when there is a 'non-fatal error' (EIO or EILSEQ) until the runtime is exceeded
or the I/O size specified is completed. If this option is used, there are two more stats that are
appended, the total error count and the first error. The error field given in the stats is the
first error that was hit during the run.
Note: a write error from the device may go unnoticed by fio when using buffered IO, as the write()
(or similar) system call merely dirties the kernel pages, unless `sync' or `direct' is used.
Device IO errors occur when the dirty data is actually written out to disk. If fully sync writes
aren't desirable, `fsync' or `fdatasync' can be used as well. This is specific to writes, as reads
are always synchronous.
The allowed values are:
none Exit on any I/O or verify errors.
read Continue on read errors, exit on all others.
write Continue on write errors, exit on all others.
io Continue on any I/O error, exit on all others.
verify Continue on verify errors, exit on all others.
all Continue on all errors.
0 Backward-compatible alias for 'none'.
1 Backward-compatible alias for 'all'.
ignore_error=str
Sometimes you want to ignore some errors during test in that case you can specify
error list for each error type, instead of only being able to ignore the default
'non-fatal error' using continue_on_error.
`ignore_error=READ_ERR_LIST,WRITE_ERR_LIST,VERIFY_ERR_LIST' errors for given error
type is separated with ':'. Error may be symbol ('ENOSPC', 'ENOMEM') or integer.
Example:
ignore_error=EAGAIN,ENOSPC:122
This option will ignore EAGAIN from READ, and ENOSPC and 122(EDQUOT) from WRITE.
This option works by overriding continue_on_error with the list of errors for each
error type if any.
error_dump=bool
If set dump every error even if it is non fatal, true by default. If disabled only
fatal error will be dumped.
Runningpredefinedworkloads
Fio includes predefined profiles that mimic the I/O workloads generated by other tools.
profile=str
The predefined workload to run. Current profiles are:
tiobench
Threaded I/O bench (tiotest/tiobench) like workload.
act Aerospike Certification Tool (ACT) like workload.
To view a profile's additional options use --cmdhelp after specifying the profile. For example:
$ fio --profile=act --cmdhelp
Actprofileoptionsdevice-names=str
Devices to use.
load=int
ACT load multiplier. Default: 1.
test-duration=time
How long the entire test takes to run. When the unit is omitted, the value is given in seconds.
Default: 24h.
threads-per-queue=int
Number of read I/O threads per device. Default: 8.
read-req-num-512-blocks=int
Number of 512B blocks to read at the time. Default: 3.
large-block-op-kbytes=int
Size of large block ops in KiB (writes). Default: 131072.
prep Set to run ACT prep phase.
Tiobenchprofileoptionssize=str
Size in MiB.
block=int
Block size in bytes. Default: 4096.
numruns=int
Number of runs.
dir=str
Test directory.
threads=int
Number of threads.
Install Now
PNG Icons
SVG Icons