-m, --min-overlap=NUM
The minimum required overlap length between two reads to provide a confident overlap. Default:
10bp.
-M, --max-overlap=NUM
Maximum overlap length expected in approximately 90% of read pairs. It is by default set to 65bp,
which works well for 100bp reads generated from a 180bp library, assuming a normal distribution of
fragment lengths. Overlaps longer than the maximum overlap parameter are still considered as good
overlaps, but the mismatch density (explained below) is calculated over the first max_overlap
bases in the overlapped region rather than the entire overlap. Default: 65bp, or calculated from
the specified read length, fragment length, and fragment length standard deviation.
-x, --max-mismatch-density=NUM
Maximum allowed ratio between the number of mismatched base pairs and the overlap length. Two
reads will not be combined with a given overlap if that overlap results in a mismatched base
density higher than this value. Note: Any occurence of an 'N' in either read is ignored and not
counted towards the mismatches or overlap length. Our experimental results suggest that higher
values of the maximum mismatch density yield larger numbers of correctly merged read pairs but at
the expense of higher numbers of incorrectly merged read pairs. Default: 0.25.
-O, --allow-outies
Also try combining read pairs in the "outie" orientation, e.g.
Read 1: <-----------
Read 2: ------------>
as opposed to only the "innie" orientation, e.g.
Read 1:
<------------
Read 2: ----------->
FLASH uses the same parameters when trying each
orientation. If a read pair can be combined in both "innie" and "outie" orientations, the
better-fitting one will be chosen using the same scoring algorithm that FLASH normally uses.
This option also causes extra .innie and .outie
histogram files to be produced.
-p, --phred-offset=OFFSET
The smallest ASCII value of the characters used to represent quality values of bases in FASTQ
files. It should be set to either 33, which corresponds to the later Illumina platforms and
Sanger platforms, or 64, which corresponds to the earlier Illumina platforms. Default: 33.
-r, --read-len=LEN-f, --fragment-len=LEN-s, --fragment-len-stddev=LEN
Average read length, fragment length, and fragment standard deviation. These are convenience
parameters only, as they are only used for calculating the maximum overlap (--max-overlap)
parameter. The maximum overlap is calculated as the overlap of average-length reads from an
average-size fragment plus 2.5 times the fragment length standard deviation. The default values
are -r 100, -f 180, and -s 18, so this works out to a maximum overlap of 65 bp. If --max-overlap
is specified, then the specified value overrides the calculated value.
If you do not know the standard deviation of the
fragment library, you can probably assume that the standard deviation is 10% of the average
fragment length.
--cap-mismatch-quals
Cap quality scores assigned at mismatch locations to 2. This was the default behavior in FLASH
v1.2.7 and earlier. Later versions will instead calculate such scores as max(|q1 - q2|, 2); that
is, the absolute value of the difference in quality scores, but at least 2. Essentially, the new
behavior prevents a low quality base call that is likely a sequencing error from significantly
bringing down the quality of a high quality, likely correct base call.
--interleaved-input
Instead of requiring files MATES_1.FASTQ and MATES_2.FASTQ, allow a single file MATES.FASTQ that
has the paired-end reads interleaved. Specify "-" to read from standard input.
--interleaved-output
Write the uncombined pairs in interleaved FASTQ format.
-I, --interleaved
Equivalent to specifying both --interleaved-input and --interleaved-output.
-Ti, --tab-delimited-input
Assume the input is in tab-delimited format rather than FASTQ, in the format described below in
'--tab-delimited-output'. In this mode you should provide a single input file, each line of which
must contain either a read pair (5 fields) or a single read (3 fields). FLASH will try to combine
the read pairs. Single reads will be written to the output file as-is if also using
--tab-delimited-output; otherwise they will be ignored. Note that you may specify "-" as the
input file to read the tab-delimited data from standard input.
-To, --tab-delimited-output
Write output in tab-delimited format (not FASTQ). Each line will contain either a combined pair
in the format 'tag <tab> seq <tab> qual' or an uncombined pair in the format 'tag <tab> seq_1
<tab> qual_1 <tab> seq_2 <tab> qual_2'.
-o, --output-prefix=PREFIX
Prefix of output files. Default: "out".
-d, --output-directory=DIR
Path to directory for output files. Default: current working directory.
-c, --to-stdout
Write the combined reads to standard output. In this mode, with FASTQ output (the default) the
uncombined reads are discarded. With tab-delimited output, uncombined reads are included in the
tab-delimited data written to standard output. In both cases, histogram files are not written,
and informational messages are sent to standard error rather than to standard output.
-z, --compress
Compress the output files directly with zlib, using the gzip container format. Similar to
specifying --compress-prog=gzip and --suffix=gz, but may be slightly faster.
--compress-prog=PROG
Pipe the output through the compression program PROG, which will be called as `PROG -c -', plus
any arguments specified by --compress-prog-args. PROG must read uncompressed data from standard
input and write compressed data to standard output when invoked as noted above. Examples: gzip,
bzip2, xz, pigz.
--compress-prog-args=ARGS
A string of additional arguments that will be passed to the compression program if one is
specified with --compress-prog=PROG. (The arguments '-c -' are still passed in addition to
explicitly specified arguments.)
--suffix=SUFFIX, --output-suffix=SUFFIX
Use SUFFIX as the suffix of the output files after ".fastq". A dot before the suffix is assumed,
unless an empty suffix is provided. Default: nothing; or 'gz' if -z is specified; or PROG if
--compress-prog=PROG is specified.
-t, --threads=NTHREADS
Set the number of worker threads. This is in addition to the I/O threads. Default: number of
processors. Note: if you need FLASH's output to appear deterministically or in the same order as
the original reads, you must specify -t 1 (--threads=1).
-q, --quiet
Do not print informational messages.
-h, --help
Display this help and exit.
-v, --version
Display version.
Install Now
PNG Icons